ARDE 1933 PART ITV-169 DETAIL NO.3, DC.36529-A, DT.06.03.2008.
C
Not Estab.
2) NOSE FUZE TYPE A 670M (EMPTY) FOR 30MM BMP-II AMMN.()
CQA(A) DRG.NO.BW.3.140.039.CB/C, DC-34241-A, DT.24.9.87(IN LOOSLY ASSEMBLED CONDITION) CONSISTING OF VARIOUS COMPONENTS AS PER ENCLOSED LIST(PASSED PROOF). PROGRAMME AND TEST PROCEDURE AS PER ALBUM NO. D-2040, SHEET NO.BW.3.140.039 II M/C (12 SHEETS) DC
C
Not Estab.
3) 51MM MORTAR BOMB BODY(EMPTY) ()
PT.NO.ITV 17 SA (02 SHEETS), SHEET NO.01 DC 37111-A DT.21.05.07 & SHEET-2, DC 37193-A DT.13.11.08.
C
Not Estab.
4) PLUG REPRESENTING FUZE B 429B ()
DRG.NO:CQA(A)/AMN/1669 PART NO:ISX-266, DC NO-35494-A, DT.29.04.93
C
Not Estab.
5) PRIMER ELECTRIC 1A/L (EMPTY) ()
CQA(A) DRG. PART NO.IQX 46 GE, DC NO.36662-A, DT.23.03.2000
C
Not Estab.
Category : DDP,DP
Grade : I,II
Size :
S
1) Ordnance Factory Bolangir
Name
Specification
Use
Status
1) PLUG REPRESENTING FUZE B 429B [65]()
Specification : DRG.NO:CQA(A)/AMN/1669 PART NO:ISX-266,DC NO-35494-A
C
Nonestab
2) 51MM MORTAR BOMB BODY(EMPTY) [65]()
Specification : PT. NO.ITV 17 SA (02 SHEETS), SHEET NO.01 DC 37111-A DT.21.05.07 & SHEET-2, DC 37193-A DT.13.11.08.
C
Nonestab
3) NOTCHED COIL [65]()
Specification : ARDE 1933 PART ITV- 169 DETAIL NO.3,DC.36529-A,DT.06.03.2008.
C
Nonestab
4) NOSE FUZE TYPE A 670M (EMPTY) FOR 30MM BMP-II AMMN.[65]()
Specification : CQA(A) DRG.NO.BW.3.140.039.CB/C, DC-34241-A, DT.24.9.87(IN LOOSLY ASSEMBLED CONDITION) CONSISTING OF VARIOUS COMPONENTS AS PER ENCLOSED LIST(PASSED PROOF). PROGRAMME AND TEST PROCEDURE AS PER ALBUM NO. D-2040, SHEET NO.BW.3.140.039 II M/
C
Nonestab
5) PRIMER ELECTRIC 1A/L (EMPTY) [65]()
Specification : CQA(A) DRG. PART NO.IQX 46 GE, DC NO.36662-A, DT.23.03.2000
C
Estab
6) CUP (EMPTY) FOR DEONATOR 356 MG[64]()
Specification : DRG. NO. QX-803, D.NO. D3(L)3934/F/83 DC NO.36103 A, DT. 29.03.96.
C
Nonestab
Category : DDP,DP
Grade : I,II
Size :
1) Heavy Alloys Penetrator Project
Name
Specification
Use
Status
1) HEAD ROCKET BODY PRE-MACHINED FOR RGB -60[03]()
39) SET OF 9 COMPONENTS FOR FLARE TRIP WIRE MK-1/L EMPTY ()
DRG. NO DD(L) 13461-A/1 SHEET I CONSISTING OF ITEM NO.1,2,3,4,5,8,13,14 AND 20.SPECN.NO CQA(A) 3807 (d)
C
Non Established
40) TORPEDO IGNITION CARTG.(EMPTY) ()
(I) CONTAINER TODRG.NO.NAD 19502/2/1 (II) RING TO DRG NO.NAD 19502/3/3(III) CARTG CASE TO DRG NO.NAD 19502/1.
C
Non Established
41) SET OF COMPONENTS FOR SIGNAL DISTRESS DAY & NIGHT 1 MK IN 1()
1)BODY 2)RING SEALING 3)CAP SMOKE(DAY) 4)CAP FLARE 5)WASHER6)SUPPORT 7)CONTAINER FLARE 8)CONTAINER SMOKE TO DRG.NOS.NAD - 8611/38, 40, 37, 39, 27, 29, 2 AND 36 RESPECTIVELY.(TOTAL EIGHT ITEMS AS ABOVE).
C
Non Established
42) EMPTY COMPONENTS FOR BASE BLEED IGNITER. ()
1. PLUG IGNITR TO DRG.NO. 02676-300002A203 2. PROTECTIVE DISC.ASSEMBLY TO DRG.NO.02676-300001A203
C
Non Established
43) GENERATOR SMOKE ASSY(EMPTY) ORANGE-3A()
DRG.NO.CQA(A)/AMN/2808 PART.NO.IQW7 GE DC 36462-A DT.02/9/98 CONSISTING OF1)LID & TEAR OFF DISC ASSY TO DRG.NO.IQW 15 SA 2)BAFFLE PLATE TO DRG .NO.IQW208 3)BODY TO DRG.NO.IQW 16 SA 4)BOTTOM PLATE TO DRG. IQW 209 5)SOLDERING TAGS TO DRG.IQW.210 WITHOUT B.
C
Non Established
44) GENERATOR SMOKE NO. 5 MK-1 (EMPTY)()
DRG. NO. ARM 1023 D2 EMPTY CONSISTING OF 1) LID 2)BAFFLE PLATE 3) BODY 4) BOTTOM 5) SOLDERING TAG 6) TEAR OFF DISC SPECN. NO. DTD & P (AIR) 207/ARM-RAW MATERIAL AS PER SPECN. IS-1993-2006 (FOURTH REV.) COLD REDUCED ELECTROLYTIC TIN PLATE)
C
Non Established
45) A SET OF LID, BOOSTER TUBE, CASE RING()
(1) LID TO DRG. NO. ARDE 2024/26 AMDT. NO. AL NO. 671 DT. 29-5-91 (2) BOOSTER TUBE TO DRG. NO. ARDE/2024/21 AMDT. NO. AL NO. 616 DT 4-10-88 (3) CASE AND RING ASSY TO DRG. NO. ARDE 2024/18 AMDT. R.NO. 1 DATED 25-8-86.
C
Non Established
Category : DDP,DP
Grade : II
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) ADOPTER BUSH FOR 81MM SMOKE GRENADE (9911358269)()
ADOPTER BUSH TO DRG.NO. 4-26941-007 DC NO. 35878 DTD. 20/12/94
C
NOT ESTABLISHED
2) SHELL 76/62MM HE PFF ASSY. EMPTY (9911357312)()
SHELL 76/62MM HE PFF ASSEMBLY EMPTY TO TRD DRG.NO.TRD- 222361.
BANGALORE TORPEDO SECTIONAL 38 mm 2m EMPTY MK 2/L TO DRG.PTNO. TX-10 GE DC(I)-33719-A DT 6/2/85 SPECN-IA-1231(g) DC (I) -35128-A DT 4/7/91
C
NOT ESTABLISHED
Category : DDP,DP
Grade : I,II
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) SET OF14 ITEMS WITH PERFORATED DISC (9911356669)[99]()
Specification : SET OF 14 COMPONENTS ( 81 MM SMOKE GRENADE EMPTY COMPONENTS)WITH DISC PERFORATED & DELAY ELEMENT(DETAILS AS PER ENCLOSEDLIST.)LOT SIZE - 2050 SET
C
Estab
Category : p
Grade : Grade III
Size :
1) Grey Iron Foundry
Name
Specification
Use
Status
1) Tail Cone Assy. of 25LBS MK-1 Bomb()
As per Drg. & Specification
C
Not Established
2) Adapter Bush()
As per Drg. & Specification
C
Not Established
Category : DP
Grade : I,II
Size :
S
1) Ordnance Factory Kanpur
Name
Specification
Use
Status
1) Al Adapter forging for 105mm IFG COL,SMK BE 3A & ILLG()
As per Drg. No. 7545/B
C
Not Estab.
2) Adopter for 105mm carrier shell()
As per Drg. No. ISX-376(finish)
C
Not Estab.
Category : DDP,DP
Grade : I,II
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) CONE (SK NO OTF/S/015) TO DRG NO 4-025998 DET NO 069 FOR 125MM HEAT[62]()
Specification : CONE (SK NO OTF/S/015) DRG NO 4-025998 DET NO 069 FOR 125MM HEAT
C
Nonestab
2) Body Upper to Drg. No. IQX-1008 in F/C DC.No. 36852-A Dated 23.09.02[63]()
Specification : Body Upper to Drg. No. IQX-1008 in F/C DC.No. 36852-A Dated 23.09.02
R
Nonestab
3) BRASS PRESSING BLANKS TO DRG NO 1896 1G FOR PRIMER 1A L MAGAZINE TO DRG NO QX 1709[63]()
Specification : BRASS PRESSING BLANKS TO DRG.NO.1896/1G FOR PRIMER 1A/L MAGAZINE TO DRG.NO.QX-1709,
P
Nonestab
Category :
Grade : Grade III
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) FORGED BLANK FOR ILLUMINATING TIME FUZE BODY TO GSF DRG. NO F-2316A SPECN .IS:734 GR.24345 WP FOR FUZE 64C()
AS PER DRG & SPECIFICATION
C
NOT ESTAB.
Category : P
Grade : I
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) SEMI MACHINE FORGED PROJECTILE BODY TO DRG.NO.F-2277B FOR 84 MMTPT()
AS PER DRG.& SPECIFICATION.
C
NOT ESTAB
2) BLANK FOR BODY CASTING FOR 84MM TPT()
AS PER DRG.& SPECIFICATION.
C
NOT ESTAB
3) PLUG REPRESENTING FUZE()
AS PER DRG.& SPECIFICATION.
C
NOT ESTAB
4) CU FUNNEL C-102 FOR 125 MM HEAT SHELL()
AS PER DRG.& SPECIFICATION.
C
NOT ESTAB
Category : P
Grade : III
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) PLUG REPRESENTING FUZE[62]()
Specification : AS PER DRG. & SPECIFICATION
R
Nonestab
2) Receiver Blank to Drg No M 9403B[70]()
Specification : Store Drg No M-8194B
C
Nonestab
3) RECEIVER TO DRG NO CTM 0108 1 TO CTM 0108 6[70]()
Specification : AS PER DRAWING
C
Nonestab
4) FORGED BLANK FOR PROJECTILE BODY TO OFAJ DRG NO F 495E[61]()
Specification : AS PER DRG
C
Nonestab
5) BLANK FOR BODY CASTING FOR 84 MM TPT[61]()
Specification : AS PER DRG.& SPECIFICATION
C
Nonestab
6) BLANK FOR DISTANCE TUBE TO TO GSF DRG NO F 1947 DCI NO 37282 A[61]()
Specification : BLANK FOR DISTANCE TUBE TO TO GSF DRG. NO:F-1947 DCI NO. 37282-A DT. 25.05.2011
R
Nonestab
7) BLANKS FOR BODY CASTING C 1946 [62]()
Specification : BLANKS FOR BODY CASTING TO GSF DRG. NO. C-1946
R
Nonestab
8) BODY SUB ASSEMBLY TO SK NO.OTE/SE/010 INF/C[62]()
Specification : AS PER DRG. & SPECIFICATION
C
Nonestab
9) FUNNEL TO DET NO 026 OF DRG NO 4 025998 WITHOUT SURFACE TREATEMENT[62]()
Specification : FUNNEL TO DET.NO.026 OF DRG.NO.4-025998 IN F/C (WITHOUT SURFACE TREATEMENT)
C
Nonestab
10) STABILIZER ASSEMBLY TO DRG NO 4 025998 det no 030Cb SK NO OTF S 028 FOR SHELL 125 HEAT[62]()
Specification : STABILIZER ASSEMBLY TO DRG. NO. 4-025998 det. no. 030Cb (SK. NO. OTF/S/028) FOR SHELL 125 HEAT
C
Nonestab
Category : P
Grade : III
Size :
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) BLANK FOR AFT CLOSURE 751 LF 9911358748
Description : BLANK FOR AFT CLOSURE 751 LF 9911358748()
Specification : BLANK FOR AFT CLOSURE 751 TO SPEC NO 00814599 MATERIAL EN-AW 7075 TO DRG NO.304200410 TO PART NO.4103408
R
Nonestab
2) BLANK FOR PLUNGER FOR 751 LF 9911358749
Description : BLANK FOR PLUNGER FOR 751 LF 9911358749()
Specification : BLANK FOR PLUNGER FOR 751 TO SPEC NO. 00814596 MATERIAL EN-AW 7075 TO DRG NO. 304101470 TO PART NO 06417888
R
Nonestab
3) BLANK FOR CARBON NOZZAL LF 9911358750
Description : BLANK FOR CARBON NOZZAL LF 9911358750()
Specification : BLANK FOR CARBON NOZZAL TO SPEC. NO. 00813350 MATERIAL MERSEN GRADE 2114 TO DRG. NO. 304066482 TO PART NO. 06413206
R
Nonestab
Category : p
Grade : 3
Size :
S
1) Grey Iron Foundry
Name
Specification
Use
Status
1) Bush of Base Booster Casing to Drg.No.AAIW/BS-0072/2A For Aerial Bomb 100/120Kgs()
As per Drg. & Specification
C
Not Established
2) Adapter Bush to Drg.No.AAIW/BS-0074 For Aerial Bomb 100/120Kgs()
As per Drg. & Specification
C
Not Established
Category : DDP,DP
Grade : I,II
Size :
S
1) Ordnance Factory Dumdum
Name
Specification
Use
Status
1) SSTEEL CONTAINER TO TU 1111()
DRG NO. ARM 1519 IN FC FOR PACKING OF TU 1111
C
NOT ESTAB.
Category : P
Grade : II
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) SHELL HEI EMPTY 30MM BMP II LF 9911358129[99]()
Specification : BODY EMPTY WITH BAND ASSY TO DRG NO.bw5.500.009Cb/c 2 SHEETSSHEET-1 DC-37321-A DT 18-10-12 SHEET-2 DC- 34241-ADT.24/09/87 SPECN.PROGRAMME AND METHOD OF TESTING AS PERSHEET NO.5w5.500.112 M/C (5 SHEET) DC-34241-A DT.24-9-87.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) FABRICATION OF SHELL BODY (EMPTY) TO DRG. NO. NAI(J) 502/2 FROM RAW MATERIAL (I/CODE NO. 0353401032) TO BE SUPPLIED BY GSF- KOLKATA[91]()
Specification : AS PER DRAWING
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) FABRICATION OF SHELL BODY (EMPTY) TO DRG. NO. NAI(J) 502/2 FROM RAW MATERIAL (I/CODE NO. 0353401032) TO BE SUPPLIED BY GSF- KOLKATA[91]()
Specification : AS PER DRAWING
C
Nonestab
2) 84mm TPT PROJECTILE BODY TO GSF DRG. NO M-11229 IN FINISH MACHINED CONDITION[61]()
Specification : AS PER DRG.
C
Nonestab
3) COOLING TANK WITH PUMP UNIT AK-630 SB AS[72]()
Specification : COOLING TANK WITH PUMP UNIT AK-630 SB AS
C
Nonestab
4) DRUM ASSY. AK-630 SB 118 SB[72]()
Specification : AS PER DRAWING
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) MOULDING ASSEMBLY OF BODY WITH CONTACT[62]()
Specification : MOULDING ASSEMBLY OF BODY WITH CONTACT TO DET. NO. C 1-2 OF DRG. NO. 3-024044 IN F/C (TO SK. NO. OTF/PG/004, OTF/PG/008, OTF/PG/009, OTF/PG/010) OTF/PG/011 DC 35811-A, DT. 19/9/94
1) FORGED BODY (FRONT PART) TO OFAJ DRG. NO. F-9G FOR 81 mm MORTAR BOMB (EMPTY BODY)[62]()
Specification : FORGED BODY (FRONT PART) TO OFAJ DRG. NO. F-9G FOR 81 mm MORTAR BOMB (EMPTY BODY)
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) TAIL UNIT 8 A WITH CAP,DES REF CQA(A)/AMN/2906 PART NO ITV 26 SA[60]()
Specification : CQA(A) 2324
C
Nonestab
2) TAIL UNIT 1A DES. REF. NO. CIA/AMN/794 PT.NO. ITV-8A[60]()
Specification : CQA(A)2308
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) CAP TO.DRG.NO.ARDE1933[60]()
Specification : CQA(A) 2324
C
Nonestab
2) CASE CARTG OF 25 PR MK 2/1/L BRASS TO DRG NO DD(L) 6557 E PART NO. RW-32[60]()
Specification : DRG NO DD(L) 6557 E PART NO. RW-32
C
Nonestab
3) CHARGE DEMOLITION 1&6 MK5 BECH EMPTY[64]()
Specification : CQA 0511
C
Nonestab
4) CLOSING DISC TO ERDL DRG NO 1005 MR[99]()
Specification : DRG.NO.ERDL DRG.1005 DET NO 3 DT.19.11-09
C
Nonestab
5) COMPONENTS FOR SQUIB PSQ 6[60]()
Specification : 1) HOUSING FOR SQUIB DRG NO PTA-L-54-01-01-102-X DT.23.2.98 2) CERAMIC BASE FOR SQUIB DRG PTA-L-54-01-01-104-X DT.23.2.98 3) SLEEVE FOR SQUIB DRG. NO. PTA-L-54-01-01-103-X
C
Nonestab
6) HOUSING DELAY SHT 2 SPECN CIA-1804[61]()
Specification : CQA(A)1804
C
Nonestab
7) INTERMEDIATE CASE DRG NO.KF/PJ/SK-2[60]()
Specification : CQA[A] SEALED DRG NO 04-749-130222-02.1E
C
Nonestab
8) IGNITER FOR ROCKET 140 MM EMPTY ASY[60]()
Specification : 1)BODY(CONTAINER) TO DRG.NO. NASK 776/9/1/1/1 (PROVISIONAL)DT. 13-5-04 QTY.1 NO. 2)DISC TO DRG NO.NASK 776/9/1/1/2 (PROVISIONAL) DT. 29-5-01 QTY 2 NOS 3) BODY (LID) TO DRG NO. NASK 776/9/1/2/1 (PROVISI ONAL) DT.29-1-04 QTY 1NO.
C
Nonestab
9) PLUG FUZE HOLE, 35 MM NO. 6 AS PER DRG. NO. CIA/AMN/2125 PART NO. ITV 95[60]()
Specification : DRG. NO. CIA/AMN/2125 PART NO. ITV 95
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) CARTG. TRAINING FOR 81 MM MOR BOMB 3 A ( EMPTY ASSY. ) DRG. NO. ARDE 2254 SHT.NO 4 PT.NO. IRW-3GE[60]()
Specification : CQA (A) 2348
C
Nonestab
2) CARTRIDGE TRAINING FOR 81MM MORTAR BOMB 3B (EMPTY ASSLY) (WITH BASE CARTRIDGE FOR CH II)TO DRG NO ARDE 2254 SHEET NO 4 PART NO IRW-3 GE[60]()
Specification : CQA (A) 2348
C
Estab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) ROUND 40 MM DRILL (PRACTICE) TO DRG. NO. AFK/SK-694-11[60]()
Specification : DRG. NO. AFK/SK-694-11
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) P.R.F. (MODIFIED) FOR 40MM AMMN. AS PER DRG.NO. AFK/SK-215-05[60]()
2) SET OF HEAD TO DRG. NO. ARM-1109-A4, DT. 19-02-1999 TO MATCH WITH DETONATOR PLUG TO DRG. NO. ARM/1109 A2, DT. 19-03-1996 FOR DET. 52[60]()
Specification : DRG. NO. ARM-1109-A4
C
Nonestab
3) PLUG REPRESENTING FUZE FOR 40MM LOW[60]()
Specification : PLUG REPRESENTING FUZE FOR 40MM LOW VELOCITY AMMN. TO DRG. NO. ODC/AFK-120-18
R
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) STRIKER DET 3 PART ITW 65 DC (I)[61]()
Specification : CQA(A) 1504
C
Nonestab
2) CTD 81 MM MOR BOMB 3A EMPTY IRE 3GE[60]()
Specification : CQA (A) 2348
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) CARTG TRAINING EMPTY ASSESMBLY FOR 120MM MORTAR BOMB TO DRG NO ARDE 1925 SHT NO 2 PT NO IRW 1GE WITH BASE CARTG 120MM CHARGE 3 TO DRG NO ARDE 2163 SHT NO 3 PT NO IRW 200 SPECN CQA A 2316[60]()
Specification : CQA (A) 2316
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) FUZE YDB 60 ASSEMBLY (EMPTY)[60]()
Specification :
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) FUZE T & P 213 MK 5 (M-R) ARDE 2020[99]()
Specification :
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1) High Explosive Factory
Name
Specification
Use
Status
1) CENTRE PIECE DET 2 PT[10]()
Specification : REF.NO. CIA/AMN/1799 DET NO. 2 PT.NO. ITW-64 DC 35817-A SPECN CQA(A) 1504(E) DC 35870-A
1) BLANK FOR DISTANCE TUBE TO OFAJ DRG NO CC 533 C[62]()
Specification : AS PER DRG.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Grey Iron Foundry
Name
Specification
Use
Status
1) TAIL UNITASSEMBLY[62]()
Specification : TAIL UNIT ASSEMBLY TO DRG.NO.AAIW/BS-0071
CONSISTING OF CONE TO DRG NO. AAIW/BS-0071/1, STABILISER FIN TO DRG NO. AAIW/BS-0071/2, STABILISER RING ASSEMBLY TO DRG NO. AAIW/BS-0071/3, AND BASE BUSH TO DRG NO. AAIW/BS-0071/4.
C
Nonestab
Category : dp
Grade : Grade I
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) BODY TO DESIGNER'S REF.ARDE-1933 DETAIL NO. 2 PART NO.ITV-17 SA SHT 1&2 SPECN CQA(A)- 2322 WITH SCREEN PRINTING AND RED MARKING AS PER DRG.ARDE-2232 PART NO.ITV-43 GF, SHT.3 PACKED WITH VCI IN PLACE OF GREASE APPLICATION[60]()
Specification : CQA(A)- 2322
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) FUZE PERCUSSION D.A. 5A (EMPTY) DRG. NO. ARDE 2236 SHEET NO 2 PART NO IQX 79 GE SPECN NO CQA(A) 0922[63]()
48) WASHER DELAY DESIGN. REF.NO. IA-1899 SHEET NO 3 PART NO.ITX 60 DC 35801-A. SPECN: CQA(A)1804[61]()
Specification : CQA(A)1804
C
Nonestab
49) WRENCH FUZING MINE APM 16 A1[42]()
Specification : CQA(A)1804
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) FUZE (EMPTY) FOR ROUND 40 MM MGL[60]()
Specification :
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ordnance Factory Ambajhari
Name
Specification
Use
Status
1) ROTOR SPRING TO CQA AMMN DRG NO 3 016919 DET 14 DC I 37284 A DT 6 7 2011 WIDTH OF STEEL STRIP TO BE RESTRICTED TO 3 minus 0 point 15 MM[00]()
Specification : ROTOR SPRING TO CQA (AMMN) DRG. NO. 3-016919 DET.-14 DC(I)37284- A DT. 6.7.2011 (WIDTH OF STEEL STRIP TO BE RESTRICTEDTO 3.00 - 0.15 MM)
C
Estab
2) STRIKER SPRING TO CQA A DRG NO 3 016919 DET 11 DC 37284 A DT 6 7 2011[00]()
Specification : STRIKER SPRING TO CQA(A) DRG.NO.3-016919 DET-11 DC-37284-A DT.6.7.2011.
C
Estab
3) CAP TO OFAJ DRG NO FS 1160A[00]()
Specification : CAP TO OFAJ DRG.NO. FS-1160A
C
Estab
4) SAFETY DEVICE TO CQA A DRG NO 4 024069 DET 2 DC 35212 A DT 12 11 91[00]()
2) 6541325748 TUBE FIRE TRANSMITTING FOR 81 MM[65]()
Specification : FIRE TRANSMITTING TUBE TO DRAWING PART NO.IRW 115,DC 37103-A DTD.02.04.2007 FOR 81MM AMMUNITION
C
Nonestab
3) 6192250491 M.F.R.C. FOR RKT 68 MM HE/HC/PRACT.[61]()
Specification : METALLIC FIN RETAINING CAP TO DRG. NO. NAD-8501 (PROV) DATED 07-04-1986 FOR ROCKET 68 MM HE/PRACTICE.
C
Nonestab
Category : dp
Grade : Grade II
Size :
S
1) Ordnance Factory Chanda
Name
Specification
Use
Status
1) 6141156252 HOUSING WITH PIN PT.DRG.NO.IQX85 SA[61]()
Specification : HOUSING WITH PIN
C
Nonestab
2) 6141800106 WASHER SPRING ITX-240 MINE AP 1B DR[61]()
Specification : WASHER, SPRING FOR ASSLY OF MINE AP 1B DIRECTIONAL.
C
Nonestab
3) 6410900880 CUP FOR PRIMER GUV-7[64]()
Specification : DRG.NO.3-027321,
C
Nonestab
4) 6431826719 CUP & BASE DETONATOR HOLDER 560 MG[64]()
Specification : CUP DETONATOR HOLDER & BASE DETONATOR HOLDER FOR DET. 560 MG FOR MINE APERS M-14.
C
Nonestab
5) 1410052010 CUP AND CAP FOR FUZE B429E[14]()
Specification : CUP & CAP FOR MAGAZINE TO DRG. NO. PROP/SK-443 FOR RECTIFICATION OF FUZE B-429E.
C
Nonestab
6) 6043000153 ADAPTOR TUBE ITV 13 A FOR 120MM PWP[60]()
Specification : ADAPTER, TUBE, ASSY. TO DRG. PART NO. ITV 13-A DC NO. 36930-A FOR 120 MM PWP.
C
Nonestab
7) 6043000210 BOMB BODY 81MM MOR C EMP ITV 9A[60]()
Specification : CQA(A) 2305(M)
C
Nonestab
8) 6043000400 ADAPTER NOSE FOR 81MM MK 1L TV 44[60]()
Specification : ADAPTER NOSE MORTAR BOMB NO. 1 TO DRG.PT.NO. TV 44 DC 36904-A DT.20/06/2003.
C
Nonestab
9) 6044000162 PRF 162A FOR BOMB 120MM MORTAR HE[60]()
Specification : PLUG REPRESENTING FUZE NO.162 A TO DRG. PART NO. ITV-17 TODC NO. 37393-A DT. 22-12-2015 FOR BOMB 120 MM MORTAR INERT, FUZED A, PLUGGED A TO DRG. PART NO. ITV 7 GA TO DC NO.37393-A DT. 22-12-2015.
C
Nonestab
10) 6044100058 PLUG REPRESENTING FZ 162A FOR 81MM[60]()
Specification : PLUG REPRESENTING FUZE NO.162 A TO DRG. PART NO. ITV-17 FOR BOMB 81 MM MORTAR INERT-FUZED A, PLUGGED A, TO DRG. PART NO. ITV-7A
C
Nonestab
11) 6120900102 FIN ASSLY WITH BAND FOR 125MM HE 1A[61]()
Specification : FIN ASSEMBLY TO DRAWING NO.4-024610 DETAIL NO.30 DC 36892-A.DT.12/04/2003 FOR 125 MM HE AMMUNITION.
C
Nonestab
12) 6121000192 CUP TO PART NO. 2-10 FOR 125MM HEAT[61]()
Specification : CUP TO PART NO. 2-10 FOR 125MM HEAT
C
Nonestab
13) 6121000193 COVER TO PT.NO. 2-11 FOR 125MM HEAT[61]()
Specification : COVER TO PT.NO. 2-11 FOR 125MM HEAT
C
Nonestab
14) 6141156300 CAPSULE PT DRG NO IQX 514[61]()
Specification : CAPSULE (ALUMINIUM-STRIP/WIRE) TO DRG.PT.NO. IQX 514DC-36852-A DT.23.9.02.
C
Nonestab
15) 6141300140 CAP CHAMBER ZINC BASE ALLY[61]()
Specification : CHAMBER (ZINC BASE ALLOY) to design.ref. CIA/AMN/474
Part No. QX- 40 DC- 35853-A DT.22-11-94.
17) 6141701300 WELL DETONATOR ITX 245 MINE AP1B DR[61]()
Specification : WELL, DETONATOR FOR ASSLY. OF MINE AP 1B DIRECTIONAL
C
Nonestab
18) 6191700029 VT HOLDER MOD FOR PINAKA RKT[61]()
Specification : VT HOLDER MODIFIED FOR PINAKA ROCKET SYSTEM TO ARDE DRAWING NO. 8603 03 99 00 02 001 00DA
C
Nonestab
19) 6192228146 DETONATOR HOLDER ARDE 1146 DET 21[61]()
Specification : DETONATOR HOLDER TO DRG. NO. ARDE-1146 DETAIL NO. 21 AL. NO.312 DT. 13-9-1977 FOR ROCKET 68 MM HE.
C
Nonestab
20) 6192355925 MAGAZINE ARDE 1146 DET NO 27[61]()
Specification : MAGAZINE TO DRG. NO. ARDE-1146 DETAIL NO.27 AL. NO.312 DT.13.9.77 FOR ROCKET 68 MM HE.
C
Nonestab
21) 6261102300 ADAPTER DRG PT SX 701 FOR 105MM TKS[62]()
Specification : ADAPTER TO DRG PT NO SX-701 DC 35779-A
C
Nonestab
22) 6270600410 ADAPTER 2 013535 53 D FOR FZ B429[62]()
Specification : ADAPTER TO DRG.NO.2-013535/53-OQ-482M,DET.NO.9,DC 36685-A FOR SHELL 130 MM.
C
Nonestab
23) 6273200062 PRF FOR SHELL 155MM ERFB BB[62]()
Specification : PRF FOR SHELL 155MM ERFB (BB/BT)/NASCHEM TO DRG. NO.PROJ/155/NASCHEM/085
C
Nonestab
24) 6330120015 PRF 117 MK 20 STL105MM IFG HE INRT[63]()
Specification : PLUG, REPRESENTING, FUZE 117 MK20 (STEEL) TO CQA(A) PART NO.ISX-475 DC-36981-A DT.12/09/04
C
Nonestab
25) 6330130100 FZ 117 DA MK 20 E WITH CAP[63]()
Specification : IA 1204 (LATEST ISSUE), DULY ACCEPTED IN PROOF AS PER CQA(A) PROOF SCHEDULE NO. CQA(A)/PS/ FZ/92/4 AND PROOF SCHEDULE NO. CQA (A)/PS/FZ/93/3.
C
Nonestab
26) 6330301100 DETONATOR HOLDER FOR SHAPED CHARGE 30MM[63]()
Specification : DETONATOR HOLDER TO DRG. NO. HE/CAST 012 DET 5 & QAP NO. HEMRL/HE/ADD/08/01 REV.00 OF 09/2008.
C
Nonestab
27) 6330600180 STRIKER MECHANISM FOR FZ B 429 CD7[63]()
Specification : STRIKER MECHANISM DRG.NO.3-016919,53-B-025Y,CD-7,DC-34920-A DT.23-7-90 EXCEPT SUB ASSEMBLY CD-6 AND ITEM DETAIL 53 FOR FUZE B 429E/B 429.
C
Nonestab
28) 6330604400 HOLDER DELAY FOR FZ B429[63]()
Specification : DELAY HOLDER TO DRG. NO. 3-016919,53-B-025Y, DET.NO.40 DC-37284-A FOR FUZE B-429
C
Nonestab
29) 6330604970 PLUG REPRESENTING FUZE B429[63]()
Specification : PLUG, REPRESENTING, FUZE B 429, B TO DRG. PART NO. ISX 266 DC 35494-A.
C
Nonestab
30) 6331451300 DETONATOR HOLDER FOR CHARGE 145 MM[63]()
Specification : DETONATOR HOLDER TO DRG.NO. HE/CAST 022 DET.5 & QAP NO.HEMRL/HE/ADD/08/01 REV.00 OF 09/2008, FOR SHAPED CHARGE145 MM.
C
Nonestab
31) 6380130100 PRIM ELE 1A/L(E) CARTG.105MM IFG SC[63]()
Specification : PRIMER ELECTRIC 1A/L EMPTY
C
Nonestab
32) 6380800110 IGNITION TUBE IRW 92 FOR 120 MM HE[63]()
Specification : IGNITION TUBE TO DRG. NO. IRW 92, DESIGNER'S REFERENCE NO. CIA/AMN/706 DC 34760-A FOR BOMB 120 MM HE.
C
Nonestab
33) 6410900120 COVER OF OBTURATOR DET 10[64]()
Specification : COVER OF OBTURATOR TO DRG.NO.3-027321 DET.NO.10 DC-36050-ADT.5/12/95 FOR PRIMER GUV-7.
C
Nonestab
34) 6410900130 CLAMPING NUT AND BASE ASSY DET 12 13[64]()
Specification : CLAMPING NUT DRG. NO. 3-027321 DETAIL NO. 12 DC 36050-A ANDBASE DRG.NO.3-027321 DET. NO. 13 DC 36050-A FOR PRIMER GUV-7IN ASSEMBLED CONDITION AS PER DRG. NO. 3-027321/4B2/CD4.
C
Nonestab
35) 6410900140 CLAMPING BUSH DET 15 PRIMER GUV 7[64]()
Specification : CLAMPING BUSH TO DRG.NO.3-027321, DETAIL NO.15 DC 36050-AFOR PRIMER GUV-7
Specification : OBTURATING DEVICE TO DRG NO.3-027321 DET.NO.CD1 DC NO.35893-A CONSISTS OF 1) SCREW DET.NO.1 DC NO.35802-A2) CONICAL SHUTTER DET.NO.2 DC NO.35802-A 3) BUSH DET.NO.3DC NO. 35802-A 4) RING DET.NO.25 DC NO.36050-A (WITHOUTPAPER DISC DET.NO.4
C
Nonestab
37) 6410900990 OBTURATOR DET NO 8 PRIMER GUV 7[64]()
Specification : OBTURATOR TO DRG.NO.3-027321, DETAIL NO.8, DC-36050-ADT.05-12-95 FOR PRIMER GUV-7.
C
Nonestab
38) 6419000027 PRIMER GUV 7 E COMPLETE FOR 125MM[64]()
Specification : EMPTY COMPONENTS OF PRIMER GUV-7, CONSISTING OF BODY TO DRGNO. 3-027321 DET 5, CUP DET 7, OBTURATOR DET 8, COVER OFOBTURATOR DET 10, CLAMPING BUSH DET 15, PACKING RING DET 6,CLAMPING NUT & BASE ASSLY DET CD4 AND OBTURATING DEVICE C
C
Nonestab
39) 6419000075 DETONATING DEVICE FOR FZ B15 EMPTY[64]()
Specification : DETONATING DEVICE FOR FZ. B15(EMPTY)TO 3-024045,DRG.NO.IQX-73 GE(WITHOUT SUB.ASSY.CD-2.2 & SED(3X1)CONST.OF(1)SUB.ASSY.CD-2.9(2)SUB.ASSY.CD-2.1(3)SUB.ASSY.TO DET 2.21(4)CONTACT TODET 2.12(5)NUT TO DET 2.16(6)LOOSE COMPONENTS CAP TO DET 2.
C
Nonestab
40) 6432100001 STEEL CUP WITH SEAL ARDE 2120 120 ARJUN[64]()
Specification : CQA(A) 5709
C
Nonestab
41) 6432100101 STEEL CUP WITH SEAL ARDE 2120 120ARJUN[64]()
Specification : CQA(A)5709
C
Nonestab
42) 6432200002 STL CUP WITH SEAL HESH 120MM ARJUN[64]()
Specification : STEEL CUP WITH SEAL FOR HESH TO DRG.PART NO. IRW 30 SA.
C
Nonestab
43) 6432200102 STL CUP WITH SEAL HESH 120MM ARJUN[64]()
Specification : STEEL CUP WITH SEAL FOR HESH TO DRG.PART NO. IRW 30 SA.
C
Nonestab
44) 6433055491 NOSE ADAPTOR TO DRG PT NO ITV-19[64]()
Specification : NOSE ADAPTER TO DRG.PT.NO.ITV-19 FOR BOMB 120 MM HE DC 36749-A
C
Nonestab
Category : dp
Grade : Grade II
Size :
S
1) Ammunition Factory Khadki
Name
Specification
Use
Status
1) 6381210301 SET OF COMPONENTS FOR PRIMER M191A2[63]()
Specification : SET OF COMPONENTS FOR PRIMER M191 A2 CONSISTING OF PLUNGER, PLUNGER GUIDE, WASHER SEALING, IGNITION ELEMENT AND INNER CASE AS PER ATTACHED ANNEXURE "A"
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) SEMI MACHINED BLANKS FOR ILLUMINATING TIME FUZE BODY TO OFAJ DRG NO CG 27 H AND PERIPHERAL GRAIN GROWTH 1MM MAX ON RADIUS[63]()
Specification : SEMI-MACHINED "BLANKS FOR ILLUMINATING TIME FUZE BODY TO OFAJ DRG NO CG 27 H & PERIPHERAL GRAIN GROWTH 1MM (MAX) ON RADIUS"
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Gun and Shell Factory
[ENR Registration]
Name
Specification
Use
Status
1) BLANK FOR DISTANCE TUBE TO TO GSF DRG. NO:F-1947 DCI NO. 37282-A DT. 25.05.2011
Description : BLANK FOR DISTANCE TUBE TO TO GSF DRG. NO:F-1947 DCI NO. 37282-A DT. 25.05.2011()
Specification : BLANK FOR DISTANCE TUBE TO TO GSF DRG. NO:F-1947 DCI NO. 37282-A DT. 25.05.2011
C
Estab
2) BODY SEMI MACHJINED M 10180 C
Description : BODY SEMI MACHJINED M 10180 C()
Specification : BODY SEMI MACHINED TO DRG NO M 10180 C
C
Estab
Category : dp
Grade : 2
Size :
S
1) Ordnance Factory Bolangir
[ENR Registration]
Name
Specification
Use
Status
1) LINER
Description : LINER()
Specification : DRG. No.5173961, DC No.36490-A, Dt.19.11.98 (IS:737-2008, GR.19000 IN O CONDITION
Specification : MS PLATE OF SIZE-1100 X 100 X 10MM (IS 2062-1994 OF ANYGRADE)
C
Nonestab
2) 0133030113 MS PLATE SIZE 450 MM[01]()
Specification : MS PLATE OF SIZE 450 X 450 X 50MM (IS-2062-1994 OF ANYGRADE)
C
Nonestab
3) 0133030120 MS ROD SIZE 50MM DIA 100MM LENGTH[01]()
Specification : MS ROD OF SIZE 50MM DIA X 100MM LENGTH (IS-2062-1994 OF ANYGRADE)
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) RAW MATERIAL OF BARREL ST ROD 40 MM DIA TO SPEC JSS 9510 06 2012 CODE REF B T I COND
Description : RAW MATERIAL OF BARREL ST ROD 40 MM DIA TO SPEC JSS 9510 06 2012 CODE REF B T I COND()
Specification : SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
R
Estab
2) Steel Round 16mm Dia 1983 GD 420 S37 EN 56 C
Description : Steel Round 16mm Dia 1983 GD 420 S37 EN 56 C()
Specification : Steel Round 16mm Dia. 1983 GD. 420 S37. (EN 56 C)
R
Estab
Category : ddp
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 3 125MM IS 4431 14C14S14 LF 0112001004
Description : STEEL ROD 3 125MM IS 4431 14C14S14 LF 0112001004()
Specification : STEEL ROD 3.125+/-0.05MM DIA IN STRAIGHT LENGTH OF 2 TO 2.5 MTRS TO SPECN.IS:4431-1978 REAFFIRMED 2004 GRADE 14C14S14 INCOLD DRAWN CONDITION.
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) SHEET MS ITEM CODE 0121020016
Description : SHEET MS ITEM CODE 0121020016()
Specification : C.R. SHEETS TO SPECN: IS-513-2008 (FIFTH REVISION) (REAFFIRMED 2013)-DD ANNEALED AND SKIN PASSED CONDICTION 2500 MM X 1000 MM X 1.6 MM.
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) Steel strip cold rolled closed annealed bright finished 3 56mm thick X 80mm wide in length of 2 mtrs LF0122223036
Description : Steel strip cold rolled closed annealed bright finished 3 56mm thick X 80mm wide in length of 2 mtrs LF0122223036()
Specification : Steel strip cold rolled closed annealed bright finished 3.56(+0.10/-0.00) mm thick X 80 +/-0.25mm wide in length of 2 mtrs to specn:- IS-513:2008 (Fifth Revision) Grade "DD" Temper 5(Annealed)
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Heavy Alloys Penetrator Project
Name
Specification
Use
Status
1) STEEL ROD DIA 10MM TO 300MM ( INCLUDING 220 MM DIA)()
Specification : MILD STEEL STRIP 100+/-1 MM WIDE x 26 BG (0.50MM) THICK IN ROLLS COLD DRAWN ANNEALED BEST SURFACE TYPE D MATT FINISHTO SPECN:-IS-513-2008 (FIFTH REVISION) WEIGHT OF EACH ROLLSHOULD BE BETWEEN 50 KG TO 100 KG.
C
Nonestab
Category : s
Grade : 3
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) ST FLAT 40X52 MM
Description : ST FLAT 40X52 MM()
Specification : ST. FLAT 40X52 MM TO SPECN. BS : 970 : PT.1: 1983 GD. 835M15 (EN-39B) IN HOT ROLLED ANNEALED CONDITION. TEST PIECE IS TO BE TESTED IN BLANK CARBURISED CONDITION
Specification : STEEL STRIP 200+/-0.5 MM WIDE X 1.1+/-0.05 MM THICK TO SPECN IS-513-TYPE DD OR BS-1449 PT-I GR-3,CS OR CR
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) MILD STEEL COMMERCIAL PLATE SIZE 2790 X 1860 X 25 MM THICK TO SPECIFICATION LF 0133020025
Description : MILD STEEL COMMERCIAL PLATE SIZE 2790 X 1860 X 25 MM THICK TO SPECIFICATION LF 0133020025()
Specification : MILD STEEL COMMERCIAL PLATE SIZE 2790 X 1860 X 25 MM THICK TO SPECIFICATION IS-2062:2011(7th REVISION) GRADE:E250 (QUALITY A)
Specification : STEEL STRIP 82+/-0.5 MM WIDE X 0.8+/-0.03 MM THICK TO SPECN:IS-513-TYPE-DD OR BS-1449-PT-I-CS-3 SEC-2.
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Small Arms Factory
Name
Specification
Use
Status
1) TOOL ALLOYS & SPECIAL STEEL FOR SMALL ARMS()
AS PER SPECIFICATION
R
Estab.
Category : S
Grade : II
Size :
S
1) Small Arms Factory
Name
Specification
Use
Status
1) TOOL ALLOYS & SPECIAL STEEL FOR SMALL ARMS[02]()
Specification : AS PER SPECIFICATION
R
Nonestab
2) ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION[03]()
Specification : ST.RD.22MM DIA IN HOT ROLLED & ANNEALED CONDITION TO SPECN IS:6527:1995,DESIGNATION X30CR 13 (FOR PLUG GAS).
R
Nonestab
3) ST FLAT SIZE 22 X 60MM[01]()
Specification : ST FLAT SIZE 22 X 60MM IN HOT ROLLED & ANNEALED CONDITIONTO SPECIFICATION BS:970:PT 1:1983 : GD 708M40,
R
Nonestab
4) ST ROUND 8 MM DIA[03]()
Specification : ST ROUND 8.00 MM DIA. TO SPECN. BS-970 PT.IIOF 1970 GD. 708 M40 (REQD.FOR-PIN FIRING OF 9MM CARBINE) ACCEPTANCE STANDARDS:MACRO ETCH TEST AS PER ASTME381 & NMIR TEST AS PER IS:4163-82
R
Nonestab
5) ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).[01]()
6) STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C[03]()
Specification : SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C.(REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
R
Estab
7) ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36[02]()
9) STEEL RD 45MM DIA IN HOT ROLLED AND ANNELED CONDITION FOR MAG[03]()
Specification : SPECNIS:5517-1993 DESIG.42CR4MO2.TEST PIECE TO BE TESTED IN`V' CONDITION.MATL. SHOULD ALSO SATISFY MACRO ETCH & NMIR TEST AS ANNEXURE NATURE-C A SEPERATE T.P. IS TO BE QUENCHED & TEMPERED BEFORE MACHINING TO ACHIEVE HARDNESS 280-335HB.
R
Nonestab
10) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE[01]()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Nonestab
11) STEEL FLAT 22X18MM FOR MAG[04]()
Specification : SPECN. IS: 5517:1993 DESIGNATION 40 NI 6 CR 4 MO2 (REQD.FOR LINK PISTON EXTN.OF MAG 7.62MM)
R
Nonestab
12) STEEL ROD 44 MM DIA FOR MAG[01]()
Specification : STEELROD 44+0.0/-0.50MM DIA.IN CUTLENGTHOF415+2.5/-00MM TO SP ECN.JSS:9510-06-2000,REV.NO.3 CODE REF.BIN T3 CONDITION WITH COMPOSITION RESTRICTED S%-0.010 MAX.P%-0.015 MAX.& (S+P)%-0. 022 MAX.FOR MAG 7.62MM.BARREL FOR OTHER PARAMETERS AS
R
Nonestab
13) STEEL FLAT 25X32MM[01]()
Specification : STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
R
Nonestab
14) STEEL SQR 37MM FOR MAG[03]()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
16) STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION[02]()
Specification : SPECN.BS:970 PT-3:1991.GD 817M40 OR 826M40 TEST PIECE TO BE TESTED IN `Z' CONDITION.
R
Nonestab
17) STEEL ROUND 27 MM[70]()
Specification : STEEL ROUND 27 MM TO SPECN.IS:5517-1993 DEGIGNATION 55C8 IN ANNEALED & COLD DRAWN CONDN. (FOR SLEEVE LOCKING BIPOD).
R
Nonestab
18) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION[01]()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
20) STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)[03]()
Specification : SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40
R
Nonestab
21) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION[01]()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
R
Nonestab
22) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.[02]()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Nonestab
23) STEEL RD 25MM DIA FOR MAG[03]()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Nonestab
24) STEEL RD 8MM DIA FOR MAG[03]()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
25) STEEL ROD 31+0.5/-0.0MM DIA.,IN CUT LENGTH OF 380+2.5/-0.0MM TO SPECN. JSS:9510-06-2000,REV.3[03]()
Specification : STEEL ROD 31+0.5/-0.0MM DIA.,IN CUT LENGTH OF 380+2.5/-0.0MM TO SPECN. JSS:9510-06-2000,REV.3 CODE REF.B IN NORMALISED CONDITION. COMPOSITION RESTRICTED: S%=0.010MAX.,P%=0.015MAX.&
(S+P)%=0.022MAX. FOR RIFLE 5.56MM. FOR OTHER PARAMETERS
R
Estab
26) STEEL ROD 32MM DIA[04]()
Specification : STEEL ROD 32.00MM DIA-0.1MM HOT ROLLED PEELED BAR IN EXACT LENGTH OF 760MM +2MM EACH PIECE TO SPECN.BS 970 PT:1:1983. GD 835 M15 WITH RESTRICTION OF S%=0.01 MAX,P%=0.015MAX,(S+P)%=0.022MAX,VACUAM DEGASED & DEVOID OF UNDESIRABLE E
Specification : STEEL STRIP TO SPECN : BS:1449:PT:1:1983 HR 15 STEEL SIZE 3.25MM X 70MM X 1250MM FOR BAR TO DRG.NO IUX-615 FOR CI (A) KIRKEE, (IFD)
R
Estab
Category : S
Grade : II
Size :
1) Rifle Factory Ishapur
Name
Specification
Use
Status
1) STEEL ROUND BAR IN DIFFERENT SIZES( 4MM TO 42MM DIA.)()
AS PER SPECIFICATION
R
Not Estab.
2) STEEL FLAT/BLANK IN DIFFERENT SIZES(16MMX35MMX630MM,5MMX5MMXLONG,14MMX6MMXLONG,36MMX36MMX600MM ETC.)()
AS PER SPECIFICATION
R
Not Estab.
3) STEEL STRIP IN DIFFERENT SIZES( 1MM TO 2MM)()
AS PER SPECIFICATION
R
Not Estab.
Category : S
Grade : III
Size :
O
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL STRIP 12 5 X 0 28 MM IS 6911 1992 LF 0323060012
Description : STEEL STRIP 12 5 X 0 28 MM IS 6911 1992 LF 0323060012()
Specification : STEEL STRIP 12.5 +/- 0.5MM WIDE X 0.28-0.02MM THICK IN FORM OF COILS OF CONTINUOUS LENGTH TO SPECIFICATION IS-6911-2017 (2nd REVISION) AMENDMENT NO. 1 & 2 , Gr X04 Cr 19 Ni 9. EACH COIL WEIGHT 5-10 KG
R
Nonestab
2) STEEL STRIP 90X2MM IS 513 BS1449 LF 0101061544
Description : STEEL STRIP 90X2MM IS 513 BS1449 LF 0101061544()
Specification : STEEL STRIP 90+/-0.5mm WIDE X 2mm THICK TO SPECN-IS-513-2008(FIFTH REV.)GRD. DD OR EDD IN ANNEALED/SKIN PASSED CONDITIONOR BS-1449 Pt-I GR. 1 OR 2 OR 3 (CR/CS) IN ANNEALED/SKINPASSED COND. ALTERNATIVE GR.1 OR 2 OR 3 OF BS-1449-Pt-I IN(HR/
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Gun Carriage Factory
Name
Specification
Use
Status
1) ST SQR 75MM TO SPECN BS 3S 144 1995[70]()
Specification : ST SQR.75 MM TO SPECN.BS:3S144:1995(1999)GD S144H
LFVD WITH CAL.SILICIDE TREATMENT.INCLUSION RATINGCHART
SECONDARY REFINING STEEL AS PER SPECN.IS:4163-82,i.e.THN/THK
SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICA
R
Nonestab
2) ST SQUARE 75 MM BS 3S144 1995 1999[70]()
Specification : STEEL SQR.75 MM TO SPECN.BS:3S144:1995(1999) GD.S144 D,
TEST CONDITION S144H.
Specification : 0329550050 ST.RD.50x2200TO SPCN.BS:3S144-95(99)GD-S144H TEST COND.S144H .LFVD(WITH CAL.SILICATE TREATMENT %OF SULPHUR & PHOS.NOT EXCEED 0.015 & 0.03.INCLUSION RATING SHOULD ALSO NOTEXCEED THE FOLLO.LIMIT SECONDARY REFINING ST.ASPERIS:4163
R
Nonestab
4) 0329580075 ST SQR 75MM TO SPECN BS 3S 144 1995[70]()
Specification : 0329580075 ST SQR.75 MM TO SPECN.BS:3S144:1995(1999)GD S144H LFVD WITH CAL.SILICIDE TREATMENT.INCLUSION RATINGCHART SECONDARY REFINING STEEL AS PER SPECN.IS:4163-82,i.e.THN/THK SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE:1.5-1, GLOBULAR OXIDE:2
R
Nonestab
5) STEEL ROUND 28 MM TO SPECIFICATION BS 3S144 1995 1999 GD S144H TEST CONDN S144H[70]()
Specification : STEEL ROUND 28 MM TO SPECIFICATION BS 3S144 1995 1999 GD S144H TEST CONDN S144H
R
Nonestab
6) STEEL ROUND 35MM DIA TO SPCN BS 3S144 1995 1999 d S144H[70]()
Specification : STEEL ROUND 35MM DIA TO SPCN BS 3S144 1995 1999 d S144H
R
Nonestab
7) ST SQR 75 MM TO SPECN BS 3S144 1995 1999 GD S144H LFVD WITH CAL SILICIDE TREATMENT INCLUSION RATINGCHART SECONDARY REFINING STEEL AS PER SPECN S 4163 82 i e THN THK SULPHIDE 1 5 1 ALUMINA 1 5 1 SILICATE 1 5 1 GLOBUL[70]()
Specification : ST SQR.75 MM TO SPECN.BS:3S144:1995(1999)GD S144H LFVD WITH CAL.SILICIDE TREATMENT.INCLUSION RATINGCHART SECONDARY REFINING STEEL AS PER SPECN.IS:4163-82,i.e.THN/THK SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE:1.5-1,GLOBULAR OXIDE: 2.0-1.
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL FLAT 45X50 070M55 OR EN9 FOR MAG
Description : STEEL FLAT 45X50 070M55 OR EN9 FOR MAG()
Specification : STEEL FLAT TO SPECIFICATION IS:5517-1993 DESIGNATION 55C8 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
R
Estab
Category : ddp
Grade : 3
Size :
S
1) Heavy Alloys Penetrator Project
Name
Specification
Use
Status
1) STEEL BLANKS FOR ADAPTER[01]()
Specification : BS 970, Dt: 3 -1991, ASTM E 381 – 01, ASTM E 112 – 12, ASTM E 45 – 05 & IS: 8791 – 1978
R
Nonestab
2) STEEL BLANKS FOR BODY BASE OF RGB 60[01]()
Specification : BS 970, Dt: 3 -1991, ASTM E 381 – 01, ASTM E 112 – 12, ASTM E 45 – 05 & IS: 8791 – 1978
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL FLAT 45X50 070M55 OR EN9 FOR MAG
Description : STEEL FLAT 45X50 070M55 OR EN9 FOR MAG()
Specification : STEEL FLAT TO SPECIFICATION IS:5517-1993 DESIGNATION 55C8 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
Specification : STEEL STRIP 85+/- 0.5 MM WIDE X 2 MM THICK TO SPECN:-IS-513 GRADE DD OR EDD IN ANNEALED/SKIN PASSED CONDITION OR BS-1449-Pt-I GR.1 OR 2 OR 3 (CR/CS) IN ANNEALED & SKIN PASSED COND. ALTERNATIVE GR.1 OR 2 OR 3 OF BS-1449-Pt-I IN (HR/HS) CON
R
Nonestab
Category : s
Grade : 3
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) ST ROD 42MM DIA
Description : ST ROD 42MM DIA()
Specification : ST.ROD 42MM DIA TO SPECIFICATION IS-4432-1988 GD-13NI 13 CR3 WITH RESTRICTIONS S%=0.010MAX.,P%=0.015MAX.&(S+P)%=0.022MAX. GROUND & POLISHED BEFORE ROLLING.NORMALISED & PICKLED.RING GRIND TESTED TO ENSURE FORGING QUALITY.04-06METERS LONG.O
R
Estab
Category : ddp
Grade : 3
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STC RD 1 inch
Description : STC RD 1 inch()
Specification : STC RD 1"(25MM) DIA TEMP-B WITH THE FOLLOWING CHEMICAL COMPOSITION:-C%=1.15 TO 1.25 SI%=0.25 MAX., MN%-0.45 MAX., S&P%=0.035 MAX. OR AS PER IS-3749-1978 GRADE T-118
R
Estab
Category : ddp
Grade : 3
Size :
S
1) Vehicle Factory Jabalpur
Name
Specification
Use
Status
1) MS SHEET 2 MM THICK[90]()
Specification : MS SHEET 2.00 MM THICK × 1250 × 2500 MM IS-1079 GR O (SK) B.C. 01.3202.0020
R
Nonestab
2) HR SHEET 4 MM X 1250 X 2500[90]()
Specification : HR SHEET 4.00MM ×1250×2500 IS 1079 GR "O" (SK)
R
Nonestab
3) HR SHEET 3 POINT15 MM X 1250 X 2500[90]()
Specification : HR SHEET 3.15MM THICK ×1000/1250×2500 IS 5986, Fe 330 OR IS:1079 GR. "O"
R
Nonestab
4) CR SHEET[90]()
Specification : CR SHEET 1.60X1250X2500 MM IS: 513 GR "D" SK
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Vehicle Factory Jabalpur
Name
Specification
Use
Status
1) HR SHEET 4 MM X 1250 X 2500[90]()
Specification : HR SHEET 4.00MM ×1250×2500 IS 1079 GR "O" (SK)
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 7 MM IS 1875 GRD 20C8 LF 0101003008
Description : STEEL ROD 7 MM IS 1875 GRD 20C8 LF 0101003008()
Specification : STEEL ROD 7(+0.025,-0.075)MM DIA IN STRAIGHT LENGTH OF 2.5 TO 3 MTRS TO SPECN.IS:1875-1992 (REAFFIRMED-2004)(FIFTH -REVISION)AMENDMENT NO.1 JAN.1993 AND AMENDMENT NO.2 NOV.1994GRADE 20C8.
Specification : STEEL STRIP SIZE 40 +/-0.5 MM WIDE X 0.35 +/-0.03 MM THICK TO SPECN:IS-513-2008 (FIFTH REVISION) GR.CR-3 OR GD I CS OFBS-1449-SECTION 1.1:1991 QUALITY IN ANNEALED AND SKIN PASSED CONDITION IN COIL OF 50 KG WEIGHT EACH.
R
Estab
Category : s
Grade : 3
Size :
S
1) Heavy Alloys Penetrator Project
Name
Specification
Use
Status
1) STEEL BLANK FOR NOZZLE PLATE FOR RGB 60[12]()
Specification : STEEL BLANK FOR NOZZLE PLATE FOR RGB 60 AS PER DRAWING NO. 0 RGB 060 1 182, AS PER LATEST REVISION
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Vehicle Factory Jabalpur
Name
Specification
Use
Status
1) M.S. BLOCK SIZE -20X170X155 FOR LEVER RHS OF MPV HULL[90]()
Specification : M.S. BLOCK SIZE -20X170X155 FOR LEVER RHS OF MPV HULL
R
Estab
2) M.S. BLOCK SIZE -20X182X125 FOR LEVER LHS OF MPV HULL[90]()
Specification : M.S. BLOCK SIZE -20X182X125 FOR LEVER LHS OF MPV HULL
R
Estab
3) MS ANGLE IRON 50x50x6MM[90]()
Specification : MS ANGLE IRON 50×50×6MM THICK IN LENGTH 5100 MM AS PER IS:2062
R
Estab
4) MS PLATE 16 MM IS 2062 GR B[90]()
Specification : MS PLATE 16 MM IS-2062 GR "B" SIZE: 16MM THICK × 1250 × 2500/2800 MM LONG
R
Estab
5) MS PLATE 25 MM THICK[90]()
Specification : MS PLATE 25 MM THICK × STD. SIZE SPECN: IS:1079, GR ST-42
R
Estab
6) STEEL ROD 45 MM DIA X 150 MM LENGTH[90]()
Specification : STEEL ROD 45 MM DIA×150MM LENGTH. SPECIFICATION EN-9 BS:970.
R
Estab
7) MS Angle 50x50x5 MM THICK[90]()
Specification : M.S. Angle (50x50x5) MM IN LENGTH OF 5 METR OR UNITS MULTIPLE LENGTH SPECN-IS:2062 GR"A"
R
Estab
8) BRIGHT BAR 55 DIA X 35 LENGTH IS 2073[90]()
Specification : BRIGHT BAR SIZE 55 DIA X 35 LENGTH IS:2073 (DRG. NO. 645-01-7321-1/C FOR FINISH COMPONENT)
R
Estab
9) FLAT 40 X 25 IN STD LENGT[90]()
Specification : FLAT 40 X 25 IN STD LENGT & SR 25 IS: 2062/1992
R
Estab
10) Bright Bar 45 dia X 85 length IS 2073[90]()
Specification : Bright Bar 45 dia X 85 length IS 2073
C
Estab
Category : s
Grade : Grade III
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION
Description : STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION()
Specification : SPECN.BS:970 PT-3:1991.GD 817M40 OR 826M40 TEST PIECE TO BE TESTED IN `Z' CONDITION.
R
Estab
2) STEEL ROD 44 MM DIA FOR MAG
Description : STEEL ROD 44 MM DIA FOR MAG()
Specification : STEELROD 44+0.0/-0.50MM DIA.IN CUTLENGTHOF415+2.5/-00MM TO SP ECN.JSS:9510-06-2000,REV.NO.3 CODE REF.BIN T3 CONDITION WITH COMPOSITION RESTRICTED S%-0.010 MAX.P%-0.015 MAX.& (S+P)%-0. 022 MAX.FOR MAG 7.62MM.BARREL FOR OTHER PARAMETERS AS
R
Estab
3) STEEL ROD 4 MM DIA
Description : STEEL ROD 4 MM DIA()
1) 9911847363 H C HCR ROUND 125 MM DIA X1500[99]()
Specification : AS PER SPECIFICATION
R
Nonestab
Category :
Grade : Grade III
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION
Description : STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION()
Specification : SPECN.BS:970 PT-3:1991.GD 817M40 OR 826M40 TEST PIECE TO BE TESTED IN `Z' CONDITION.
R
Estab
2) STEEL ROD 44 MM DIA FOR MAG
Description : STEEL ROD 44 MM DIA FOR MAG()
Specification : STEELROD 44+0.0/-0.50MM DIA.IN CUTLENGTHOF415+2.5/-00MM TO SP ECN.JSS:9510-06-2000,REV.NO.3 CODE REF.BIN T3 CONDITION WITH COMPOSITION RESTRICTED S%-0.010 MAX.P%-0.015 MAX.& (S+P)%-0. 022 MAX.FOR MAG 7.62MM.BARREL FOR OTHER PARAMETERS AS
R
Estab
3) STEEL ROD 4 MM DIA
Description : STEEL ROD 4 MM DIA()
1) STEEL BAR TO SPECN NO IS 4431 78 DESIGNATION 14C 14S14 COLD DRAWN IN STRAIGHT LENGTH OF 2 TO 3 MTRS SIZE 22 MM DIA
Description : STEEL BAR TO SPECN NO IS 4431 78 DESIGNATION 14C 14S14 COLD DRAWN IN STRAIGHT LENGTH OF 2 TO 3 MTRS SIZE 22 MM DIA()
Specification : STEEL BAR TO SPECN.NO.IS:4431-78 DESIGNATION 14C 14S14 (C/D) IN STRAIGHT LENGTH OF 2 TO 3 MTRS. SIZE 22 -0.052 MM DIA
R
Estab
2) hot rolled cold drawn carbon steel round to specn BS 970 Pt I 1983 grade O80M40 in straight length of 3 metres size 17mm minus 0 point 08 dia
Description : hot rolled cold drawn carbon steel round to specn BS 970 Pt I 1983 grade O80M40 in straight length of 3 metres size 17mm minus 0 point 08 dia()
Specification : HOT ROLLED COLD DRAWN CARBON STEEL ROUND TO SPECN BS:970-PT-I 1983 GRADE 080M40 IN STRAIGHT LENGTH OF 3 METRES(10 %MAX.SHORT DOWN TO 2-3 METRES PERMITTED) SIZE:17.00-0.08MM DIA
R
Estab
3) NORMALISED AND PEELED CARBON STEEL ROUND BARS TO SPECN BS 970 PT I 1983 GRADE 080M40 IN STRAIGHT LENGTH OF 2 TO 3METRES SIZE 21MINUS 0POINT1MM DIA
Description : NORMALISED AND PEELED CARBON STEEL ROUND BARS TO SPECN BS 970 PT I 1983 GRADE 080M40 IN STRAIGHT LENGTH OF 2 TO 3METRES SIZE 21MINUS 0POINT1MM DIA()
Specification : NORMALISED AND PEELED CARBON STEEL ROUND BARS TO SPECN BS:970-PT-I-1983 GRADE 080M40 IN STRAIGHT LENGTH OF 2 TO 3METRES,SIZE:21.00 - 0.1MM DIA. (10 % MAX.SHORT LENGTH OF 1.5 METRE ALLOWED.)
10) STEEL ROUND 6 POINT 5 MM 0 POINT 018 MM DIA BS 970 PART 1 80 M 50
Description : STEEL ROUND 6 POINT 5 MM 0 POINT 018 MM DIA BS 970 PART 1 80 M 50()
Specification : STEEL ROUND 6.5MM - 0.018 MM DIA ,BS 970 PART-1 80 M 50
R
Estab
11) STEEL ROUND 7 BY 8 INCH 22 MM DIA BS 970 EN 9
Description : STEEL ROUND 7 BY 8 INCH 22 MM DIA BS 970 EN 9()
12) STL ROD 22 MM DIA BS 970 PT 5 70 A 72 IS 4072 70 C 6
Description : STL ROD 22 MM DIA BS 970 PT 5 70 A 72 IS 4072 70 C 6()
Specification : STEEL ROD 22 MM DIA BS 970 PT 5, 70 A 72 / IS 4072, 70 C 6
R
Estab
13) ST ROD 120MM DIA X 1 MTR L IS 3748 1990 T 105 CR 5
Description : ST ROD 120MM DIA X 1 MTR L IS 3748 1990 T 105 CR 5()
Specification : ST. ROD 120MM DIA X 1 MTR(L) IS 3748:1990 T-105 CR-5
R
Estab
14) STEEL BLOCK 6 INCH SQUARE X 8 INCH LONG BS 970 EN 15
Description : STEEL BLOCK 6 INCH SQUARE X 8 INCH LONG BS 970 EN 15()
Specification : STEEL BLOCK 6" SQUARE X 8" LONG BS 970 EN-15
R
Estab
15) STEEL ROUND 22 MM DIA BS 970PT 1 1983 605 M 36
Description : STEEL ROUND 22 MM DIA BS 970PT 1 1983 605 M 36()
Specification : STEEL ROUND 22 MM DIA BS 970PT-1:1983 605 M-36
R
Estab
16) STEEL FLAT 2 INCH X 1 INCH TO SPECN IS 963 1958
Description : STEEL FLAT 2 INCH X 1 INCH TO SPECN IS 963 1958()
Specification : STEEL FLAT 2" X 1" TO SPECN IS-963-1958
R
Estab
17) STEEL ROUND 16 MM DIA BS 970 PT I 83 GDE 420 S 37
Description : STEEL ROUND 16 MM DIA BS 970 PT I 83 GDE 420 S 37()
Specification : STEEL ROUND 16 MM DIA BS 970 PT-I:'83 GDE 420 S 37
R
Estab
18) STEEL ROD 25 MM DIA SPCN IS 6603 1972 GR 40CR13
Description : STEEL ROD 25 MM DIA SPCN IS 6603 1972 GR 40CR13()
Specification : STEEL ROD 25 MM DIA SPCN IS 6603:1972 GR 40CR13
R
Estab
19) STEEL ROUND 3 BY 4 INCH DIA TO IS 6603 GR 40 CR 13
Description : STEEL ROUND 3 BY 4 INCH DIA TO IS 6603 GR 40 CR 13()
Specification : STEEL ROUND 3/4" DIA TO IS 6603 GR 40 CR-13
R
Estab
20) STEEL ROD 32 MM DIA SPCN IS 6603 2001 GDE 40 CR 13
Description : STEEL ROD 32 MM DIA SPCN IS 6603 2001 GDE 40 CR 13()
Specification : STEEL ROD 32 MM DIA SPCN IS 6603 2001 GDE 40 CR 13
R
Estab
21) STEEL ROUND 32MM DIA TO BS 970 EN 26 OR EN 36 B
Description : STEEL ROUND 32MM DIA TO BS 970 EN 26 OR EN 36 B()
Specification : STEEL ROUND 32MM DIA TO BS 970 EN-26 OR EN-36 B
R
Estab
22) STEEL ROD 32 MM DIA TO SPCN TY 14 1 2884 80 IN CD
Description : STEEL ROD 32 MM DIA TO SPCN TY 14 1 2884 80 IN CD()
Specification : STEEL ROD 32 MM DIA TO SPCN. TY:14-1-2884-80 IN CD
R
Estab
23) STEEL ROUND 32 MM DIA GRD 50 SPN TY 14 1 2884 80
Description : STEEL ROUND 32 MM DIA GRD 50 SPN TY 14 1 2884 80()
Specification : STEEL ROUND 32 MM DIA GRD 50 SPCN TY 14 1 2884 80
R
Estab
24) STEEL PIPE OD 70MM ID 40 MM TO IS 3074 05 DESIG C
Description : STEEL PIPE OD 70MM ID 40 MM TO IS 3074 05 DESIG C()
Specification : STEEL PIPE OD 70MM ID 40 MM TO IS :3074-05 DESIG C
R
Estab
25) STEEL ROUND 1 3 BY 4 INCHES DIA TO SPCN BS 970 EN 19T
Description : STEEL ROUND 1 3 BY 4 INCHES DIA TO SPCN BS 970 EN 19T()
Specification : STEEL ROUND 1 3/4'' DIA TO SPCN BS 970 EN -19T
R
Estab
26) STEEL ROUND 32 MM DIA BS 970 PT I 832 M 13
Description : STEEL ROUND 32 MM DIA BS 970 PT I 832 M 13()
Specification : STEEL ROUND 32 MM DIA BS 970 PT I 832 M 13
R
Estab
27) STEEL ROUND 48 MM DIA BS 970 PT I 832 M 13
Description : STEEL ROUND 48 MM DIA BS 970 PT I 832 M 13()
Specification : STEEL ROUND 48 MM DIA TO BS 970 PT-1 : 832 M-13
R
Estab
28) STEEL ROUND 3 POINT 5 MM PLUS MINUS 0 POINT 025 MM DIA LENGTH 1 MTR A
Description : STEEL ROUND 3 POINT 5 MM PLUS MINUS 0 POINT 025 MM DIA LENGTH 1 MTR A()
29) STEEL ROUND 80 MM DIA to spec 070 M 55 TO
Description : STEEL ROUND 80 MM DIA to spec 070 M 55 TO()
Specification : STEEL ROUND 80 MM +1 MM DIA TO SPECN. 070 M 55 TO BS-970:PT-1-1983 IN HOT ROLLED,PEELED & MAGNETICALLY CRACK DETECTION PASSED CONDN.END OF BAR SQUARE,YIED STREES-2% PRROF STRESS 650 MPA (MIN),ELONGATION-10% (MIN),LENGTH 1.2 MTR. OR IN MUL
R
Estab
30) STEEL RD 70 MM DIA TO BS 970 PT I 83 GDE 070 M 55
Description : STEEL RD 70 MM DIA TO BS 970 PT I 83 GDE 070 M 55()
Specification : STEEL RD 70 MM DIA TO BS 970 PT-I: 83 GDE 070 M 55
R
Estab
Category : s
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL STRIP 40x0point35 mm LF 0121060051
Description : STEEL STRIP 40x0point35 mm LF 0121060051()
Specification : STEEL STRIP SIZE 40 +/-0.5 MM WIDE X 0.35 +/-0.03 MM THICK TO SPECN:IS-513-2008 (FIFTH REVISION) GR.CR-3 OR GD I CS OFBS-1449-SECTION 1.1:1991 QUALITY IN ANNEALED AND SKIN PASSED CONDITION IN COIL OF 50 KG WEIGHT EACH.
2) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
Description : STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Estab
3) STEEL RD 8MM DIA FOR MAG
Description : STEEL RD 8MM DIA FOR MAG()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
4) Steel Strip
Description : Steel Strip()
Specification : Steel Strip Size :- 1,8MM THICK X270 MM WIDE X1600 MM LONG TO SPECN. IS:7226-1974 GRADE C-40. COLD ROLLED & ANNEALED CONDN.
Note: GRAIN DIRECTION SHOULD BE ALONG THE LENGTH
R
Estab
5) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION
Description : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
R
Estab
6) STEEL RD 38MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN. IS:5517 -1993, DESIGNATION 40 C8
Description : STEEL RD 38MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN. IS:5517 -1993, DESIGNATION 40 C8()
9) STEEL RD 25MM DIA FOR MAG
Description : STEEL RD 25MM DIA FOR MAG()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Estab
10) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
Description : STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
11) STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)
Description : STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)()
Specification : SPECN BS: 970:PT-3:1991 GD.420S29 OR 431 S29
R
Estab
12) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
R
Estab
13) STEEL SQR 37MM FOR MAG
Description : STEEL SQR 37MM FOR MAG()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
R
Estab
14) STEEL ROD 35 MM DIA
Description : STEEL ROD 35 MM DIA()
Specification : STEEL RD. 35MM DIA +/- 0.25MM IN HOT ROLLED REELED,PEELED & ANNEALED CONDITION TO SPECN JSS:9510:06:2000(REV. NO.3)CODE REF.'B'.TEST PIECE TO BE TESTED IN 'T' CONDITION.MATERIAL SHOULD ALSO SATISY THE TEST AS PER ANNEXURE 'A' NATURE A A
R
Estab
15) RAW MATERIAL OF BARREL ST. ROD 40.0 MM DIA TO SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
Description : RAW MATERIAL OF BARREL ST. ROD 40.0 MM DIA TO SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.()
Specification : SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
R
Estab
Category : s
Grade : 3
Size :
S
1) Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).
Description : ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).()
2) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
Description : STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Estab
3) STEEL RD 8MM DIA FOR MAG
Description : STEEL RD 8MM DIA FOR MAG()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
4) Steel Strip
Description : Steel Strip()
Specification : Steel Strip Size :- 1,8MM THICK X270 MM WIDE X1600 MM LONG TO SPECN. IS:7226-1974 GRADE C-40. COLD ROLLED & ANNEALED CONDN.
Note: GRAIN DIRECTION SHOULD BE ALONG THE LENGTH
R
Estab
5) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION
Description : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
R
Estab
6) STEEL RD 38MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN. IS:5517 -1993, DESIGNATION 40 C8
Description : STEEL RD 38MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN. IS:5517 -1993, DESIGNATION 40 C8()
9) STEEL RD 25MM DIA FOR MAG
Description : STEEL RD 25MM DIA FOR MAG()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Estab
10) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
Description : STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
11) STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)
Description : STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)()
Specification : SPECN BS: 970:PT-3:1991 GD.420S29 OR 431 S29
R
Estab
12) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
R
Estab
13) STEEL SQR 37MM FOR MAG
Description : STEEL SQR 37MM FOR MAG()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
R
Estab
14) STEEL ROD 35 MM DIA
Description : STEEL ROD 35 MM DIA()
Specification : STEEL RD. 35MM DIA +/- 0.25MM IN HOT ROLLED REELED,PEELED & ANNEALED CONDITION TO SPECN JSS:9510:06:2000(REV. NO.3)CODE REF.'B'.TEST PIECE TO BE TESTED IN 'T' CONDITION.MATERIAL SHOULD ALSO SATISY THE TEST AS PER ANNEXURE 'A' NATURE A A
R
Estab
15) RAW MATERIAL OF BARREL ST. ROD 40.0 MM DIA TO SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
Description : RAW MATERIAL OF BARREL ST. ROD 40.0 MM DIA TO SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.()
Specification : SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
R
Estab
Category : ddp
Grade : 3
Size :
S
1) Gun and Shell Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 13 MM PLUS MINUS 0 POINT 1 MM DIA TO SPECN BS 970 PT 3 1991 STEEL GRADE 070 M 20 COLD DRAWN IN A LENGTH OF 2 POINT 5 MTRS TO 2 POINT 7 MTRS
Description : STEEL ROD 13 MM PLUS MINUS 0 POINT 1 MM DIA TO SPECN BS 970 PT 3 1991 STEEL GRADE 070 M 20 COLD DRAWN IN A LENGTH OF 2 POINT 5 MTRS TO 2 POINT 7 MTRS()
Specification : STEEL ROD 13 MM +/- 0.1 MM DIA TO SPECN BS-970 PT-3-1991 STEEL GRADE 070 M 20 COLD DRAWN IN A LENGTH OF 2.5 MTRS TO 2.7 MTRS
2) Steel Flat Size 6 X 22mm in Hot Rolled Normalised Condition for Revolver
Description : Steel Flat Size 6 X 22mm in Hot Rolled Normalised Condition for Revolver()
Specification : Steel Flat Size:- 6 X 22mm in Hot Rolled & Normalised Condn.To Specification Bs:970:Pt.1:1983:Gd.070m55. Material To Be Tested in Hardened & Tempered Condition as Per Ruling Section & Seperate Test Piece Need to be heat treated to achi
R
Estab
Category : s
Grade : 3
Size :
S
1) Small Arms Factory
Name
Specification
Use
Status
1) STEEL FLAT 125X 8X 530 MM LONG IN CUT LENGTH[01]()
Specification : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993 DESIGNATION 55C8 TEST PIECE TO BE TESTED AS PER SPECN.TOLLERANCE ON WIDTH +/-2MM,ON THICKNE
SS +/-0.25MM.
R
Estab
Category :
Grade : Grade III
Size :
S
1) Gun and Shell Factory
Name
Specification
Use
Status
1) STEEL ROUND 30 point 10 MM plus 0point5MM dia TO SPCN 53 x M1 0 TY 14 1 2232 77 and OST B 84 748 81 ANNEALED AND PEELED CONDITION TO 2 point 50 MTRS TO 3 MTRS in straight length rods[03]()
Specification : STEEL ROUND 30.10 MM (+0.5MM/-0.00MM) DIA TO SPCN 53 X M1-0 TY-14-1-2232-77 & OST B 84-748-81, ANNEALED AND PEELED CONDITION TO 2.50 MTRS TO 3.00 MTRS
IN STRAIGHT LENGTH MUST BE SUBJECTED TO 100% INSPECTION USING ULTRASONIC FLAW DETE
Specification : BOX WOOD NO.PZ-1 TO DRG. NO. ARDE 1953 SHEET NO. 1,2&3 AND ARDE-1953, DET NO.4 .(OFBA/RK/504,505,506,& 507) RESPECTIVELY.
R
Estab
Category : DDP,DP
Grade : II
Size :
1) Ordnance Factory Nalanda
Name
Specification
Use
Status
1) WOODEN CRATE[65]()
Specification : OFN/BMCS/M-92/WOODEN CRATE
C
Nonestab
Category : dp
Grade : Grade III
Size :
S
1) Ordnance Equipment Factory
Name
Specification
Use
Status
1) TIMBER SISSOO HARD WOOD(NON CONIFEROUS) SCANTLING GR. I SIZE 150 MM X 300 MM X 762 MM FOR 4 NOS FINISHED COMPONENTS[21]()
Specification : AS PER REQUIREMENT AND SPECIFICATION
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ordnance Equipment Factory
Name
Specification
Use
Status
1) SHOOKS VARIOUS OF DIFFERENT GRADE & DIMENSIONS[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
2) TIMBER CHIR PLANK/SLEEPER OF VARIOUS GRADES & DIMENSIONS[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
3) TIMBER HARD WOOD/TIMBER SISSOO HARDWOOD (NON-CONIFEROUS) PLANK/SLEEPER OF VARIOUS GRADES & DIMENSIONS[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
4) TIMBER SOFT WOOD PLANK/SLEEPER OF VARIOUS GRADES & DIMENSIONS [21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
5) WOODEN CRATE/CRATE WOOD PACKING VARIOUS[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) AMMUNITION CONTAINER BOX C-55A (PLYWOOD)[99]()
Specification : AMMN. CONTAINER BOX C 55A (PLYWOOD) FOR AMMN. CONT. ASSY 173A TO DRG.PT.NO. ISV 626A DC 37283-A DT. 30/06/2011 REFER WITH DRG.NO.PT.NO. ISV-557GA DC 37283-A DT. 30/06/2011
Specification : CRATE WOOD 12-A TO DRG.PT.NO.ISV-483-A DC NO.36999-A DATED 02/02/2005 SPECN:-IA-948(a,k)DC(I)36868-A,AIDE MEMOIRE W/4NOTE 1:-SPECIAL INSTRUCTION FOR TEST FOR CRATE WOOD 12A IS ENCLOSED.NOTE 2:-ADVANCE SAMPLE 05 NOS.ARE REQUIRED WHEN ITEM
C
Estab
Category : p
Grade : 3
Size :
S
1) Rifle Factory Ishapur
Name
Specification
Use
Status
1) CHEST FOR PISTOL AUTO 9MM 1A.[70]()
Specification : CHEST PISTOL AUTO 9MM 1A (TO HOLD 20 PISTOLS ) TO DRG.NO. CQA(SA) SK-605 (LATEST DC-26041-SA DT.26-2-05) FOR PISTOL AUTO 9MM 1A.
C
Nonestab
2) Chest Rifle 5.56mm (Wooden) Capacity-10 Rifles with accessories.[79]()
Specification : Chest Rifle 5.56mm (Wooden) Capacity-10 Rifles with accessories. to DS CAT No.1005-560403 (SHT.-1 & SHT.-2) (Latest DC-26483-SA FOR SHT.-1 & DC-26197-SA FOR SHT.-2) For Rifle 5.56mm INSAS.
Specification : TO DRG. PT NO. ITX-39A DC 35916A DTD. 21.02.95. SPECIFICATION : CQA(A) 1817(s) DC 36789-A, DTD. 22.10.2001 WITH (1) DUST CUP DRG. PT. NO. ITX-283 DC 35597-A DTD. 06.10.93 = 01 NO. (2) FASTNER FOR SAFETY PIN CORD DRG. NO. ITX-284 DC 35916-
C
Nonestab
2) PACKING TO DRG[62]()
Specification : PACKING TO DRG.NO.4-24929/3 K33/001 DC NO.35604-A, DT.11.10.93 [MATERIAL TO SPECN: IND/ME/645(a),DC NO.3754-ME,DT.12.12.02.]
C
Nonestab
3) PRESSURE PAD TYPE A & B ASSEMBLY PART[61]()
Specification : PRESSURE PAD TYPE "A" ASSEMBLY PART ITX-60 SA DC 35916-AS DTD. 21.02.95 AND PRESSURE PAD TYPE "B" DC 35916A DTD. 21.02.95 TO SPECIFICATION CQA(A) 1817(s) DC 36902-A DTD. 10.06.2003 RESPECTIVELY (TO BE SUPPLIED BOTH THE ITEM AS A SET, (EA
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) AFT CLOSURE INSULATOR FOR HEAT-551()
DRG.NO. TRD-2-2-2243
C
Estab
2) SEALING RING FOR HEAT-551()
DRG.NO. TRD-1-2-2246
C
Estab
3) DIAPHRAGM FOR HEAT-551()
DRG.NO. TRD-2-2-2244
C
Estab
4) "O" RING 89.1X5.7 MM()
DRG.NO. TRD-845
C
Estab
Category : P
Grade : II
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) PACKAGE TO DRG NO.08040002000000000 (9911358292)()
PACKAGE TO DRG.NO. ARDE 08040002000000000PB, DTD. 14/05/2015
ADDITIVE LINER TO DRG. NO ARDE-1716 DET NO. 7 (PROV.) R. NO. 8 DTD. 10/01/2012 ARD-2423
C
NOT ESTABLISHED
4) PRIMER GASKET F1301-036530-D (2013436143)()
DRG.NO. F1301-036530-D DC NO. 36783-A DT. 19/9/01 INDEGENOUS MATERIAL SPECN: IND/ME/884:2005
C
NOT ESTABLISHED
5) RUBBER HOOD (2058130002)()
DRG. NO. F-1301-078691-C DC NO. 35131-A DATE 5/7/91. SPECN:-IND/ME/884:2015
C
NOT ESTABLISHED
6) ARMING DEVICE CASING ASSY FOR 551 (9911357821)()
DRG.NO. 5209556
C
NOT ESTABLISHED
7) CARRIER 11A ISV-468A FOR HE & ILLU. (6573810100)()
CARRIER, AMMUNITION 11-A (PLASTIC) TO DRG. PT. NO. ISV-468-ADC-37090-A DT 27-01-07 TO SPECN:CQA (A)-2804(m) DC-36202-A DT 7/11/96
C
NOT ESTABLISHED
8) BASE PLATE 7.8 MM FOR HEAT/TPT (6170444700)()
DRG NO F-1301-015080-K DC 36862-A DT. 11/11/02 SPECN:- F-1301-901520-L (b) (CQA-0305) DC NO.36766-A DT. 14/7/2001
C
NOT ESTABLISHED
9) BASE PLATE 8.5 MM FOR HE/ILLG. (6170444690)()
DRG NO. F-1301-015081-L DC 36862-A DT. 23/08/2005 SPECN:- F-1301-902040-K (b) (CIA-0308) DC 36766-A DT. 14/07/2001
C
NOT ESTABLISHED
10) CAP AND LOCK BOTTOM F1301-905060-P (2013998518)()
CAP TO DRG. NO. F1301-024351-J DC NO 36522-A DT. 10/02/99 & LOCK BOTTOM TO DRG. NO. F1301-029651-F DC NO. 36771-A DT. 31/07/01 SPECN:- F1301-905060-P DT 7/1/91
C
NOT ESTABLISHED
11) CAP AND BOTTOM SPECN F1301-905060-P (9911350158)()
CAP TO DRG NO-F1301-024351-J DC NO.36522-A DT 10/02/99 SPECN F1301-905060-P DT 7/1/91 & BOTTOM TO DRG NO F1301-029650-EDC NO.36816-A DT.25/02/02 SPECN.F1301-905060-P DT.07/01/91
C
NOT ESTABLISHED
12) MOULDING OF PRIMER BODY & CONTACT (9911349627)()
Specification : DRG NO. 902-01-401 DC-17988-W DT. 20-06-1994. MATERIAL: ACRYLONITRILE BUTADIENE RUBBER COMPOUND TO SPECN.:-IND/ME/914(PROV) DC-3496-ME DT.06-02-98GRADE C OR D HARDNESS 55 TO 70.
Specification : ADDITIVE LINER TO DRG. NO ARDE-1716 DET NO. 7 (PROVISIONAL) R. NO. 8 DATED 10/01/2012 ARD-2423..
R
Nonestab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) O RING LF 9911357865[99]()
Specification : "O" RING 71*1.6 DRG.NO.TRD-122259
C
Nonestab
2) O Ring 74 5x3 TO DRG NO TRD 845a LF 6170444650[61]()
Specification : O Ring 74.5x3 TO DRG NO TRD 845a
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) O RING 71 X 1 65 PART NO 6413243 LF 2013999913[20]()
Specification : O-RING 71 X 1.65 PART NO.6413243 DRG.NO.TRD-1-1-2962
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) O RING 78 X 2 PART NO 6409795 LF 2013999909[20]()
Specification : O-RING 78 X 2 PART NO.6409795 DRG.NO.TRD-1-1-2960
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) PLASTIC PACKAGE FOR PREFRAG 100-120 KG BOMB [9911358232]()
Specification : PLASTIC PACKAGE FOR PRE-FRAG OFAB 100-120 KG BOMB TO DRG. ARDE.0303 00 04 00 00 000 12 PB & SPECN.NO. DRDO-ARDE-ADM-HSD-002-2012. REV 1 DTD 26 MAY'2014.
P
Nonestab
Category : p
Grade : Grade II
Size :
S
1) Ordnance Factory Khamaria
Name
Specification
Use
Status
1) CARBON NOZZLE BLANK FOR 84 HEAT-551[99]()
Specification : CARBON NOZZLE BLANK TO DRG NO.6413 206/DRG.NO.TRD-1-2-2242.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) O RING 78X2 LF 2013436144
Description : O RING 78X2 LF 2013436144()
Specification : 'O' RING 78X2 (2013436144)
R
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) CAP AND BOTTOM FOR 84MM HEAT 751 LF 9911358519
Description : CAP AND BOTTOM FOR 84MM HEAT 751 LF 9911358519()
Specification : CAP-PART NO.4102085 TO OEM DRG.NO.304031170/TRD DRG.NO.4.2.2516 & BOTTOM- PART NO..6414118 TO OEM DRG.NO. 304101481/TRD DRG.NO. 1.2.2409.
R
Nonestab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) PRIMER GASKET PART NO 6409794 LF 2013999910
Description : PRIMER GASKET PART NO 6409794 LF 2013999910()
Specification : PRIMER GASKET PART NO.6409794 TO OEM DRG.NO.304083636/ TRD.DRG.NO.1.2.2370
R
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) O RING LF 9911357868
Description : O RING LF 9911357868()
Specification : "O" RING 71*1.8 DRG.NO.TRD-122260
R
Estab
2) O RING LF 9911357869
Description : O RING LF 9911357869()
Specification : "O" RING 71*1.65TO DRG.NO.TRD122263
R
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) SLEEVE DRG Point number QX 655 LF 2103716522
Description : SLEEVE DRG Point number QX 655 LF 2103716522()
Specification : SLEEVE DRG Point number QX 655 LF 2103716522
R
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Dehu Road
Name
Specification
Use
Status
1) PLUG FOR 81MM AT AL[62]()
Specification : DRG NO 902.01.401 DC NO 17988 W DTD 20/06/1994
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Khamaria
[Deemed Registration]
Name
Specification
Use
Status
1) BALL INSERT FRONT & REAR (9911339844)
Description : BALL INSERT FRONT & REAR (9911339844)()
Specification : BALL INSERT, FRONT TO DRG. NO. F1301-115180-C DC NO 35780-A DT 22/8/94 SPECN:-F1301-910840-C (CQA-4914) DC(I)-33419-ABALL INSERT REAR TO DRG. NO. F1301-036770-C DC NO-35780-A DT 22/08/94 SPECN:-F1301-902230-C (CQA-4904) DC(I) 33419-A(NEOP
C
Estab
Category : p
Grade : 2
Size :
S
1) Ordnance Factory Khamaria
[Deemed Registration]
Name
Specification
Use
Status
1) SLIPPING RING (6770430100)
Description : SLIPPING RING (6770430100)()
Specification : SLIPPING RING TO DRG. NO. F-1301-152220-B DC NO-36730-A DTD. 15/01/01 SPECN:- F1301-924320-D (CQA-4919)DC NO-36730-A DTD15/01/01
C
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[Deemed Registration]
Name
Specification
Use
Status
1) CAP AND BOTTOM SPECN: F1301-905060-P (9911350158)
Description : CAP AND BOTTOM SPECN: F1301-905060-P (9911350158)()
Specification : CAP TO DRG NO-F1301-024351-J DC NO.36522-A DT 10/02/99 SPECN F1301-905060-P DT 7/1/91 & BOTTOM TO DRG NO F1301-029650-EDC NO.36816-A DT.25/02/02 SPECN.F1301-905060-P DT.07/01/91.
C
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[Deemed Registration]
Name
Specification
Use
Status
1) CAP AND LOCK BOTTOM F1301-905060-P (2013998518)
Description : CAP AND LOCK BOTTOM F1301-905060-P (2013998518)()
Specification : CAP TO DRG.NO. F1301-024351-J DC NO. 36522-A DT. 10/02/99 AND LOCK BOTTOM TO DRG.NO. F1301-029651-F DC NO. 36771-A DT. 31/07/01 SPECN: F1301-905060-P DT. 07/01/91
C
Estab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Bhandara
[ENR Registration]
Name
Specification
Use
Status
1) Sleeve Rubber
Description : Sleeve Rubber()
Specification : SLEEVE RUBBER TO CI (A) DRG NO.IT X 223 DC(I) 29442-A(OFBA/ CORDT/22 DTD 25.2.70)TO SPECN.CIA 0516(C)37024-A DT03/08/05
1) FILLING PLUG FORGING 1000 LBS L F NO 2015995448[20]()
Specification : FILLING PLUG FORGING TO DRG. NO. OFM/32788. [DRG.ENCLOSED].
C
Nonestab
Category :
Grade : Grade III
Size :
S
1) Ordnance Factory Muradnagar
Name
Specification
Use
Status
1) FORGING FOR LUG 318 FOR 1000 LBS L F NO 6220601406[62]()
Specification : FORGING FOR LUG SUSPENSION NO.318 AS PER DRG.OFM-31738B TO BE SUPPLIED DULY HEAT-TREATED (HARDENED & TEMPERED) TO ACHIEVE HARDNESS OF 180-250 VPN,Y.S. 44KG/SQR MM MIN.,UTS -60-75 KG/SQR MM,ELONGATION-18% MIN.0N 5.65 UNDER ROOT "A".(DRGS.
C
Nonestab
2) FORGING FOR LUG 243 AS PER DRG FOR 1000 LBS L F NO 6220700172[62]()
Specification : FORGING FOR LUG 243,DRG. No,OFM-32616ATO BE SUPPLIED DULY HEATTREATE D(HARDENED & TEMPERED)TO ACHIEVE HARDNESS OF 210-261 VPN.YS=46 KG/MM.SQ.MIN,UTS=70-85KG/MM.SQ,EL=5. 65 ROOT A-16% MIN.OR ON YFOUR ROOT A-20% MIN.
1) SHUTTER PLATE TBRL LF NO 9911358300
Description : SHUTTER PLATE TBRL LF NO 9911358300()
Specification : SHUTTER PLATE TO DRG.NO.TBRL/MMG-H/MK1/053/R0
C
Nonestab
Category : p
Grade : 3
Size :
S
1) Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) SET OF14 ITEMS WITH PERFORATED DISC LF 9911356669
Description : SET OF14 ITEMS WITH PERFORATED DISC LF 9911356669()
Specification : SET OF 14 COMPONENTS ( 81 MM SMOKE GRENADE EMPTY COMPONENTS)WITH DISC PERFORATED & DELAY ELEMENT(DETAILS AS PER ENCLOSEDLIST.)LOT SIZE - 2050 SET
R
Nonestab
Category : p
Grade : 3
Size :
S
570
Elastomer lining works
W 22/23 chemical zone m.i.d.c ambernath Chemical zone ambernath m.i.d.c Ambernath Maharashtra
PIN1 : 421501
Phone No. : 2610723
GSTIN : 27AACFE2169E1ZO
60) Tape Nylon 66,26 mm BS 850 Kg UD Resin Treated()
As per specification
R
Non Established
61) Tape Nylon 66,26 mm BS 850 Kg UD ()
As per specification
R
Non Established
62) Tape Nylon 66,21 mm BS 600 Kg UD()
AS PER SPECIFICATION
R
Non Established
63) Tape Nylon 20 mm BS 5680 N UD ()
As per specification
R
Non Established
Category : DDP,DP
Grade : I,II
Size :
S
1) Ordnance Equipment Factory
Name
Specification
Use
Status
1) POLYESTER WADDING HOLLOW SILCONIZED 350 GSM IN 91 CM[21]()
Specification : AS PER APPENDIX "A" ATTACHED TO PROV. SPECN. S/6252/A/TC-6
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1) Ordnance Clothing Factory Shahjahanpur
Name
Specification
Use
Status
1) FABRICATION OF COAT ECC IMP VER[21]()
Specification : FABRICATION OF COAT ECC IMP VER
FABRICATION (200001 - TAILOR SKILLED MACHINE - I, 200008 - TAILOR SKILLED HAND - I, 200015 - SERGING & 200016 - METAL EYELET FIXING) OF COAT ECC IMPROVED VERSION, AS PER SPECIFICATION NO. S/3558/A/TC-15/C
E
Estab
Category :
Grade : Grade III
Size :
SS
1) Ordnance Equipment Factory Hazaratpur
Name
Specification
Use
Status
1) CORD NYLON 1785 N[90]()
Specification : JSS:4020-9:1999 (Rev.No. 1)
R
Estab
2) TAPE WOVEN NYLON 26MM WR UVR TREATED BLACK [90]()
Specification : ADRDE/SPECN/70(b)
R
Estab
3) TAPE WOVEN NYLON 30MM WR UVR TREATED BLACK [90]()
Specification : ADRDE/SPECN/70(b)
R
Estab
4) CORD NYLON 3120N[90]()
Specification : JSS:4020-09:2007 (REV. NO. 2)
R
Estab
Category : DDP,DP
Grade : I,II
Size :
S
1) Ordnance Equipment Factory
Name
Specification
Use
Status
1) ANKLET BD OG[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
2) F.R. TREATED TWINE NYLON OLIVE GREEN (IS:220)[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
Specification : Prov.IND/TC/1550 (7202/PK dt.21/09/2013) AND ATTACHED RELEVE
R
Nonestab
22) FABRICATION OF LINER INNER FOR TEFS 2M UNIT[21]()
Specification : AS PER REQUIREMENT & SPECIFICATIONÂÂ
R
Nonestab
23) Fabrication of TEFS 4M Fly Inner[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
24) Fabrication of Tent Fly Outer 4M Unit[21]()
Specification : AS PER REQUIREMENT & SPECIFICATION
R
Nonestab
25) TRADE FABRICATION OF BAG KIT UNIVERSAL WITH PV DOPE DYED FABRIC OG[21]()
Specification : FABRICATION OF BAG KIT TO BE CARRIED ON AS PER SPECN. NO.
R
Nonestab
26) TRADE FABRICATION OF NET MOSQUITO R/M POLY KHAKI WITH CALICO BORDER[21]()
Specification : AS PER REQUIREMENT AND SPECIFICATION
R
Nonestab
27) TRADE FABRICATION OF PACK WITH ALUMINIUMFRAME (MODIFIED)[21]()
Specification : AS PER REQUIREMENT AND SPECIFICATION
R
Nonestab
28) TRADE FABRICATION OF RAIN JACKET WITH INTEGRATED HOOD AND TROUSER; SIZE- LARGE[21]()
Specification : AS PER REQUIREMENT AND SPECIFICATION
R
Nonestab
29) Bandolier 1A Complete[21]()
Specification : Drg. No. ARDE-1942, Sheet no. 3 Drg. Part No. ISV-423 DC No. ..............
R
Nonestab
Category : p
Grade : Grade III
Size :
1) Ordnance Parachute Factory
Name
Specification
Use
Status
1) COTTON TAPE FOR PARACHUTE SD 25 MM SCOURED. SPECN. NO IS: 3255-1979 Reaffirmed 2003[2101774715]()
Specification : SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)Ther
R
Nonestab
Category :
Grade : Grade III
Size :
SS
1) Ordnance Parachute Factory
Name
Specification
Use
Status
1) Tape Para-aramid 26 mm, 1600 kgf Tubular[2010797689]()
Specification : ADRDE/SPECN/2002/57
R
Nonestab
2) TAPE PARA-ARAMID 25 MM, 1000 KGF[2010797688]()
Specification : SPECN. NO. ADRDE/2002/57.
R
Nonestab
Category :
Grade : Grade III
Size :
SS
1) Ordnance Parachute Factory
Name
Specification
Use
Status
1) WEBBING PARA-ARAMID 44 MM, 9000 KGF[2101877405]()
Specification : ADRDE/SPECN/2002/57(a) REQD. for BRAKE PARA (HYBRID) FOR TEJAS (LCA)
R
Nonestab
Category :
Grade : Grade III
Size :
SS
1) Ordnance Parachute Factory
Name
Specification
Use
Status
1) FABRIC NYLON 58 GM UD 105 CM MIN WIDTH EXCLUDING SELVEDGE[2101221384]()
Specification : SPECN NO. AS PER TECH. PARTICULARS
(a) MASS/SQ MET : 58 GM (MAX)
(b) BREAKING STRENGTH, BOTH WAYS : 60 KGF (MIN)
(C) TEARING STRENGTH, BOTH WAYS : 1.7 KGF (MIN)
(d) AIR POROSITY : 7-10 CU.FT/SQ.FT/SEC.
(e) THICKNESS:0.11M, MAX AT A P
Specification : ADRDE/QMS/TDTM/F/2012/02 DATED 19 JAN 2012 and
(i) The fabric shall have an initial spray rating of 80, 80, 70 minimum when tested as per AATCC 22 or equivalent test method.
(ii) The manufacturer shall submit a certificate of complia
