AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Specification
AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
Specification
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
Specification
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
2101786939
33609
Metre
2322
110170194
Ordnance Parachute Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208004
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
Specification
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
Specification
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
Specification
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
2101797674
79224
Metre
2336
OPF/ADVANCE VR/EOI/JULY-17/ TAPE-02
Ordnance Parachute Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208004
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
Specification
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65.
Specification
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65
IS : 3255-1979 Except that :- (i) In appearance shade,
finish & in all other respect not defined in this IS Specn.
the material shall conform to the sealed pattern held in the
custody of the Controller, CQAT&C, Kanpur. (ii) there shall be no presence of starch. (iii) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(iv) 100% Sampling Testing & Inspection will be resorted to Sampling plan as per annexure (a) attached.
Packing and marking as per schedule CIT&C/PMS/65.
Specification
IS : 3255-1979 Except that :- (i) In appearance shade,
finish & in all other respect not defined in this IS Specn.
the material shall conform to the sealed pattern held in the
custody of the Controller, CQAT&C, Kanpur. (ii) there shall be no presence of starch. (iii) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(iv) 100% Sampling Testing & Inspection will be resorted to Sampling plan as per annexure (a) attached.
Packing and marking as per schedule CIT&C/PMS/65.
