SPECIFICATION NO. : IS : 4726-1984 and to the following exceptions :- (i) The breaking strength shall be carried out by revelled strip method after conditioning the test specimen at 65 + 2% RH & 27 + 2 C for 24 Hrs. No individual reading for breaking strength test for warp and weft shall be
less than the value shown in ISI specn. NO.IS:4726-84.
(ii) 100 % Sampling/Testing/Inspection shall be resorted
(iii)Roll length shall be 80 M or above.(iv) A Flag allowance of 50 cm for each major defect flagged except for continuous defect which shall be given a one meter allowance for each meter in which defect occurs
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
2101221216
68858
Metre
2007
110170573
Ordnance Parachute Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208004
SPECN-IS:4741-1965(Amdt-1.Reafirmed 2003) except for pull strength, which should be 4Kgf(Min). For Plastic Washer Thickness (under pressure 200g/cm squire) 1.14mm & Dia12.52 mm of best trade quality
Specification
IS:4741-1965(Amdt-1.Reafirmed 2003) except for pull strength, which should be 4Kgf(Min). For Plastic Washer Thickness (under pressure 200g/cm squire) 1.14mm & Dia12.52 mm of best trade quality
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
2111654009
191001
Number
2008
110170526
Ordnance Parachute Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208004
AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Specification
AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
Specification
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
Specification
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
Specification
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
Specification
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
Specification
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65.
Specification
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65
IS : 3255-2024 Except that :-
(i) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur.
(ii) There shall be no presence of starch.
(iii) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(iv) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) att ached.
Packing and marking as per schedule CIT&C/PMS/65.
SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING.
Except that : - Shade should be as per approved sample held with QCM/OPF.
